Stubby Handlebar Kit multiClip TOUR Ready-to-install kit suitable for the selected vehicle model. The illustration shows the exemplary scope of delivery of a multiClip kit. This varies depending on the motorcycle model. With the stubby: significantly higher seating comfort without having to install a superbike kit with tubular handlebars directly. The stubby can also be adjusted lower again if needed. Please order separately: Handlebar ends With parts certificate. In Germany, the kit must be approved and registered at a testing facility after installation. The KIT consists of: multiClip Tour Ø43 mm Upper fork bridge gpRacing black Small parts- up to approx. 5.5 cm higher / up to approx. 8 cm wider

Mother - cardan M24X1,5- OE Replacement

Adjustable Shift Lever BMW R1200GS from 2010-2018 The shift lever is mounted on the original gear lever. The installation time is half an hour. The joint pin of the gear lever and the ball head are replaced with a longer one. Shifting with the shift lever leads to a more relaxed shifting process. Due to a model change from BMW, it is necessary for you to send us a photo of your gear lever. World travelers have been waiting a long time for this option, as shifting while standing is almost impossible. Of course, the original shifting process remains intact. If the handlebars are too low for you, we have something for that as well. Our Handlebar Adapter 1008-901449 is ideal for you. For those with a tight knee angle, we recommend our stable, lowered footpeg 1008-907938b . This way, world travelers are well equipped.

MV Shift Lever R1200RT LC and R1250RT LC The icing on the cake for the best-selling tourer in the world, the BMW R1200RT LC R1250RT MV shift lever for the best-selling tourer. For even more relaxed touring, we have now developed a shift lever for the BMW R1200RT LC and R1250RT LC that is mounted on the original gear lever. The shift lever is adjustable in all directions. With the second lever, you have the option to shift all gears from above, but you can also shift as usual. The shift lever is attached to the original gear lever. The interesting part is the selectable shifting. The original gear lever remains intact. With our additional lever, you can elegantly shift all gears from above. This also gives your foot a break. The lever is adjustable axially and in height. The RT also loves to lean, and even in this position, you can still shift up.

The BMW R nineT Crown for R nineT, Scrambler, Urban, Pure, and Racer - Ø 46 mmCrown your R nineT!In just 3 minutes of installation time with a clamp, you can complete your retro.This not only improves the appearance, but the engine also receives better cooling.The exhaust crown in cylindrical shape was not cast, but meticulously turned and milled from solid aluminum.The price is for a pair.Design patent 40 2019 000 798.5 protected.All items were mounted and tested on original motorcycles - without any modifications.

Extended Reverse Lever BMW R18 An elegant and interesting looking solution for the reverse lever on the BMW R18, which is mounted quite low and hidden. We have solved this problem and created a sensible and visually reminiscent solution to the 1940s. Many motorcycles in the 40s came with a reverse gear as standard. The adapter is slipped over the original lever and secured with 2 M6 threaded pins underneath. We offer the lever in polished and black anodized finishes and for two models. Once for models with 60mm and 100mm. Please measure the length of your original reverse lever and then select the corresponding length. You can also choose the composition of the lever, ball holder, and ball individually. Please write to us about this as a note with your order.

This is a used part being offered Vehicle: BMW R18 Manufacturer: MV Verholen Condition: normal signs of use Description: sold as shown, scratchesPart number: 10392 An elegant and interesting looking solution for the reverse lever on the BMW R18, which is mounted quite low and hidden. We have solved this problem and created a sensible solution that visually recalls the 1940s. Many motorcycles in the 40s came with a reverse gear as standard. The adapter is slipped over the original lever and secured with 2 M6 threaded pins underneath.

MV Seat Lowering for BMW R1250GS from 2021 onwards With our lowering kit, the front seat is lowered by 10mm. 10mm may seem like a small amount, but it can make a big difference when your boot heel is firmly on the ground, providing a sense of security while maneuvering. Installation time is only 1 minute.

Puig Windscreen NAKED A windscreen in the naked bike look. Made from durable polycarbonate. It offers good protection against wind and weather and improves aerodynamics. Installation instructions and required mounts are included.Technical Data:Height:   345 mmWidth:   320 mmColor:   light smoke gray Manufacturer:   Puig

Navigation Mount for BMW 750GSWith this elegant solution, you can attach your TomTom, Garmin, or other navigation devices.The mount is designed to fit only the small BMW windscreen No. 1 = height 216 mm.The mount is secured to the upper screws that hold the windscreen in place.All items have been mounted and tested on original motorcycles - without any aftermarket modifications.

Navigation Mount for BMW Navigation Devices with 25mm Ball With our mount, you have the option to attach a ball to your navigation device and position it on the handlebar. The power supply is achieved through a Y-connector at the input of the onboard socket. The onboard socket is not used from the outside. After switching off, the navigation device remains on for about 4 minutes. Our system prevents the battery from being deeply discharged. The cable is included in the price and is connected to the onboard socket. However, it is only suitable for the use of navigation devices or mobile phones, not for additional lights. The latest MV device holder for your BMW navigation device The mount replaces an M8 handlebar mounting screw. The ball is made of polished aluminum and has a diameter of 25.4 mm. All balls are equipped with a rubber ring, making them non-slip and vibration-dampened.   The RamMount holder (Item No. 1008-109011) must be ordered separately.

Navigation Holder for BMW F900XR for BMW Navigation Device Elegant solution at eye level. For mounting navigation devices on the BMW F900XR. Since the original BMW navigation device is mounted directly on the handlebar bridge, you have to look down far while riding. This is a safety concern and can be dangerous. Therefore, we offer this very elegant and sensible solution. Our holder is screwed onto existing screws of the fairing part. See photo. The instruments are not covered by this. We offer the holder in two versions: for navigation devices that are mounted with a 25 mm ball. If you want to mount your navigation device higher with the original BMW mounting, you will need our holding system for BMW navigation devices. Please select the appropriate item when placing your order.

Navigation Mount for BMW F900XR Navigator with 25mm Ball Elegant solution at eye level. For mounting navigation devices on the BMW F900XR with a 25mm ball. Since the original BMW navigation system is installed directly on the handlebar bridge, you have to look down far while riding. This is a safety concern and can be dangerous. Therefore, we offer this very elegant and sensible solution. Our mount is screwed onto existing screws of the fairing part. See photo. The instruments are not obscured by this. We offer the mount in two versions: for navigation devices that are mounted with a 25mm ball. If you want to position your navigation device higher using the original BMW mount, you will need our holding system for BMW navigation devices. (1008-10383) Please select the appropriate item when placing your order.

TomTom Mount for Your BMW R1200GS Adventure LC With this mount, you can easily and securely attach the original TomTom holder to the bracket above the speedometer. Our mount is suitable for bracket diameters of 12mm and 16mm. The integrated grooves ensure that the mount is securely fixed to the bracket (light mounting traces may occur). The mount is compatible with all TomTom Rider motorcycle navigation devices. made from high-strength aluminum CNC machined black anodized complete with all mounting materials easy installation Made in Germany Delivery includes: Mount upper and lower part 2 pcs. mounting screws for the mount 4 pcs. mounting screws for the TomTom holder Attention, only the mount with screws is delivered, not the navigation device and/or accessories! Usage list: R1200GS Adventure LC all models with a bracket above the speedometer (some special accessories, please check if available!)

TomTom Mount for Your BMW R1250GS and R1250GS Adventure With this mount, you can easily and securely attach the original TomTom holder to the bracket above the speedometer. Our mount is suitable for bracket diameters of 12mm and 16mm. The integrated grooves ensure that the mount sits securely and does not twist on the bracket (light mounting traces may occur). The mount is compatible with all TomTom Rider motorcycle navigation devices. made from high-strength aluminum CNC machined black anodized complete with all mounting materials easy installation Made in Germany Delivery includes: Mount upper and lower part 2 pcs. mounting screws for the mount 4 pcs. mounting screws for the TomTom holder Attention, only the mount with screws is delivered, not the navigation device and/or accessories! Usage list: R1250GS + R1250GS Adventure all models with a bracket above the speedometer (please check for special accessories if available!)

TomTom Mount for Your BMW S1000XR With this mount, you can easily and securely attach the original TomTom holder to the bracket above the speedometer. Our mount is suitable for bracket diameters of 12mm and 16mm. The integrated grooves ensure that the mount sits securely on the bracket (light mounting traces may occur). The mount is compatible with all TomTom Rider motorcycle navigation devices. made from high-strength aluminum CNC machined black anodized complete with all mounting materials easy installation Made in Germany Delivery includes: Mount upper and lower part 2 pcs. mounting screws for the mount 4 pcs. mounting screws for the TomTom holder Attention, only the mount with screws is delivered, not the navigation device and/or accessories! Usage list: S1000XR all models with a bracket above the speedometer (please check if special accessories are available!)

Navigator VI ECE

TomTom Navihalter für Ihre BMW R1200GS und R1200GS Adventure Mit diesem Halter können Sie die originale TomTom Halterung am Bügel oberhalb des Tachos leicht und sicher befestigen. Unsere Halterung ist sowohl für Bügeldurchmesser von 12mm als auch von16mm geeignet. Durch eingearbeitete Rillen sitzt die Halterung verdreh sicher auf dem Bügel (es können leichte Montagespuren entstehen). Der Halter passt für alle TomTom Rider Motorrad Navigationsgeräte. gefertigt aus hochfestem Aluminium CNC gefräst schwarz eloxiert komplett mit allem Befestigungsmaterial leichte Montage Made in Germany Lieferumfang: Halter Ober- und Unterteil 2 Stk. Befestigungsschrauben für den Halter 4 Stk. Befestigungsschrauben für den TomTom Halter Achtung, geliefert wird nur die Halterung mit Schrauben nicht das Navi und/oder Zubehör!  Verwendungsliste: R1200GS + R1200GS Adventure alle Modelle mit Bügel über dem Tacho (zum Teil Sonderzubehör bitte prüfen, ob vorhanden!)

TomTom Navihalter für Ihre BMW R1200GS LC Mit diesem Halter können Sie die originale TomTom Halterung am Bügel oberhalb des Tachos leicht und sicher befestigen. Unsere Halterung ist sowohl für Bügeldurchmesser von 12mm als auch von16mm geeignet. Durch eingearbeitete Rillen sitzt die Halterung verdreh sicher auf dem Bügel (es können leichte Montagespuren entstehen). Der Halter passt für alle TomTom Rider Motorrad Navigationsgeräte. gefertigt aus hochfestem Aluminium CNC gefräst schwarz eloxiert komplett mit allem Befestigungsmaterial leichte Montage Made in Germany Lieferumfang: Halter Ober- und Unterteil 2 Stk. Befestigungsschrauben für den Halter 4 Stk. Befestigungsschrauben für den TomTom Halter Achtung, geliefert wird nur die Halterung mit Schrauben nicht das Navi und/oder Zubehör!  Verwendungsliste: R1200GS LC alle Modelle mit Bügel über dem Tacho (zum Teil Sonderzubehör bitte prüfen, ob vorhanden!)

Needle Bearing   - Drive Shaft - Drive Housing - Original Spare Part

Needle jet for Bing constant vacuum carburetor type 64-3. Total length 16.5 mm; largest diameter 7.5 mm; for atomizer air system - Replacement part for Bing carburetors: 64/26/301 - 304 64/28/301 - 304 64/32/301 - 304 64/32/313 - 314 64/32/321 - 324 64/32/351 - 352 64/32/357 - 362 64/32/3030 64/32/3040 64/32/377

Needle jet for Bing constant vacuum carburetor type 64-3. Total length 16.5 mm; largest diameter 7.5 mm; for atomizer air system - Replacement part for Bing carburetors: 64/26/315 - 318 64/32/305 - 306 64/32/335 - 348

Needle Sleeve

Angeboten wird hier ein NeuteilFahrzeug: S1000R, S1000RR, M1000R, M1000RR Hersteller: BMWNeupreis: 1.067,37 € Zustand: siehe Bilder Beschreibung: wird verkauft wie abgebildetTeilenummer: 46518359991