Is your bike leaning too much? Then our side stand extension for upright parking of the bike is just what you need.Especially with a "loaded" bike, it can happen that your motorcycle tips over in the original angle under unfavorable ground conditions. The adapter shoe provides the side stand with a corresponding extension, widening, and height increase, making it easier to stand the bike upright.Simply slide it on and tighten the internal hex screw.The adapter does not fit the Adventure model. There is a separate adapter for the 2010 model year.Height increase: 17mmAll items have been mounted and tested on original motorcycles - without any modifications.

Is your bike leaning too much? Then our side stand extension for upright parking of the bike is just what you need.Especially with a "loaded" bike, it can happen that your motorcycle tips over in the original angle under unfavorable ground conditions. The adapter shoe provides the side stand with a corresponding extension, widening, and height increase, making it easier to stand upright.Simply slide it on and tighten the internal hex screw.You may need to smooth the original weld slightly. We have found that the welds can vary slightly even within the same model series. (Example image)Height increase: 17mmAll items have been mounted and tested on original motorcycles - without any modifications.

A well-known problem that has cost most motorcyclists their last nerves! You ride your machine off the road over stock and stone, and a short break is included. But it's easier said than done. Parking the vehicle on soft ground is a real issue! A small board or a similar base is usually never at hand when needed.Touratech has the solution:With the side stand foot enlarger, the contact area is increased by more than double, and the exhausting task of lifting the fully loaded bike is now a thing of the past. A mix of stainless steel and black anodized aluminum gives this enlarger a great look and full stability. Thanks to a secure attachment of the foot enlarger, it is always with you, saving you a lot of trouble and frustration with this practical accessory.Fits only with original BMW side stands for lowered chassis.

Is your bike leaning too much?Then our side stand extension for upright parking of the bike is just what you need.Especially with a "loaded" bike, it can happen that your motorcycle tips over in the original angle under unfavorable ground conditions. The adapter shoe provides the side stand with a corresponding extension, widening, and height increase, making it easier to stand upright.Simply slide it on and tighten the internal hex screw.You may need to smooth the original weld slightly. We have found that the welds on the same model series can vary in quality.Dimensions B 60 x L 85 x H 17 mmAll items have been mounted and tested on original motorcycles - without any modifications.

A well-known problem that has cost most motorcyclists their last nerves! You ride your machine off the road over stock and stone, a short break is included. But easier said than done. Parking the vehicle on soft ground is a real problem! A small board or a similar base is usually never at hand when needed.Touratech has the solution: With the side stand foot enlargement, the contact area is increased by more than double, and the exhausting task of lifting the fully loaded bike is now a thing of the past. A mix of stainless steel and black anodized aluminum gives this enlargement a great look and full stability. With a secure attachment of the foot enlargement, it is always with you, saving you a lot of trouble and frustration with this practical accessory.Not suitable for lowered chassis.Suitable for special model R1200GS "Rallye" with special equipment "Sport chassis".Attention: Regardless of the respective model year, different side stands have been installed, so we recommend additionally checking the shape of your side stand.Please use for: - Wide shape 1021-01-045-5276-0- Narrow shape 01-045-5275-0

When fully loaded or on uneven surfaces, the motorcycle is at risk of sinking slightly on the side stand.A precisely machined widening plate, which can be quickly screwed onto the side stand and eliminates this danger, is now available from us!The HEPCO&BECKER side stand enlargement! partly more than double the contact area secure stand of the machine on all surfaces oxidation-resistant anodized aluminum and black coated upper steel counter holder easy installation with just a few screws does not require ABE or registration

When fully loaded or on uneven surfaces, the motorcycle is at risk of sinking slightly on the side stand.A precisely machined widening plate, which can be quickly screwed onto the side stand and eliminates this danger, is now available from us!The HEPCO&BECKER side stand enlargement! partly more than double the contact area secure stand of the machine on all surfaces oxidation-resistant anodized aluminum and black coated upper steel counter plate easy installation with just a few screws does not require ABE or registration

When fully loaded or on uneven surfaces, the motorcycle is at risk of sinking slightly on the side stand.A precisely machined widening plate, which can be quickly screwed onto the side stand and eliminates this danger, is now available from us!The HEPCO&BECKER side stand enlargement! partly more than double the contact area secure stand of the machine on all surfaces oxidation-resistant anodized aluminum and black coated upper steel counterplate easy installation with just a few screws does not require ABE or registration

SIDEPIPE_GB25 - HATTECH Complete System for R80 R / R100 R Mystic as well as for R80 and R100 GS - Paralever - Complete system with header pipe and muffler - With EU type approval Complete system with header pipe (with interference pipe for better performance) and muffler - With EU type approval - available in various surface variants Hattech continues its classic and proven path with the new exhaust systems. Details about the mufflers: lying flat with interference pipe for better performance pipe connections are plugged and held with springs completely made of stainless steel all components welded using TIG welding available polished or brushed pleasant, sonorous, bassy sound at the volume level of the original noise reduction insert screwed into the muffler outlet and secured by welding EU type approval no registration in the vehicle documents necessary Note: Side stand must be modified/replaced by the customer. Note: Disassembly of the center stand required

The silencer protector (2 parts) for the BMW R Nine T Scrambler is a direct replacement for the original component and with the weight of only about 40g contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. For these thermically stressed parts we use special high-temperature prepreg material (see FAQ) to avoid burning and staining of the parts.   Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. For this. thermic stressed. carbonpart. we use special high-temperature prepreg material (see FAQ) to avoid burning and staining of the part.  Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. For this. thermic stressed. carbonpart. we use special high-temperature prepreg material (see FAQ) to avoid burning and staining of the part.  Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The Silencer protector (rear) for the BMW R NineT Serie is a direct replacement for the original component.it contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. The carbon part is made of special high-termperature prepreg (FAQ) to avoid burning and staining of the part. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The silencer protector for the BMW R nineT Urban GS from 2016 in carbon is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. For this thermic stressed part we use a special high-temperature prepreg material to avoid burning and staining of the part.  

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. For this thermic stressed part we use special high-temperature prepreg material (see FAQ) to avoid burning and staining of the part. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm. Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silverAll items have been mounted and tested on original motorcycles - without any modifications.

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm. Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silver Only suitable for brake levers with round rubber!All items have been mounted and tested on original motorcycles - without any modifications.

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm. Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silver Only suitable for brake levers with round rubber!All items have been mounted and tested on original motorcycles - without any modifications.

Easy to install + lightweight + high protection effectWe have taken on these challenges and developed a cylinder protection that meets all these criteria!Made from 3mm thick aluminum and attached at the designated points, the Touratech cylinder protection for the water-cooled R1200GS withstands "tip-overs" as well as stronger "impacts." Scratched valve covers or even holes in them are a thing of the past.Tested, among other places, in Madagascar, the protection has reliably proven its performance.A "must-have" for every boxer engine with its protruding cylinders!- can be mounted together with original BMW engine protection bars- made of 3mm thick silver anodized aluminum- easy and quick to installDelivery includes:Cylinder protection right + left, mounting materials, installation instructionsTo combine with Touratech crash bars, please order 045-5130!

Vehicle-Specific Information:  from 01.08.1988 for 2 disc brakesSA Sintered Metal Street Brake Pads for Front (SA) A sintered mixture specifically designed for front wheel brakes that offers improved braking performance under all operating conditions. An ideal alternative to OE brake pads for optimal performance on the road.

n.v.

BMW R Nine T Scrambler'16 Carbon seat cowl for Mono seat R Ninet The seat cover for the single seat in carbon for the BMW R NINET scrambler replaces the original part using the original Befestigungspunkte.Unser exhaust heat guard weighs only 87g. In the foreground weight savings are (usually savings of approximately 70% compared with the original component) and higher carbon Steifigkeit.Das part was completely in accordance with the latest guidelines in the autoclave prepreg (see FAQ) material and in the next step, as with us usual, covered for protection against environmental influences with a clear plastic coating. This plastic coating exceeds the usual clear lacquer coating in the protection, scratch resistance and resistance enormous. But not only technically can score the coating, but also highlights the three-dimensional effect of the carbon structure still further.

JMP Skan Monitor 2 Lithium Battery monitoring with your smartphone: With the JMP Skan Monitor 2 and the new free Apple or Android app "JMP BatteryMonitor II", you can quickly and easily check the charge status of your battery. Only with a consistent, positive charge status of the battery is the full capacity and usability guaranteed. The positive charge status also prevents potential early damage or failure of the battery. Continuous recording captures the battery's charge status during rides and can be accessed later. The file with the data can be sent via email from the smartphone and displayed in Excel. This allows you to quickly identify where the charging voltage dropped or was too high. Additionally, a defective regulator can be quickly identified. Furthermore, the new app can also accurately check starting processes (starter, cable connections, etc.) and charging processes (alternator, cables, etc.). This saves long troubleshooting in case of problems. In case of low battery status or other issues, a notification can warn the rider depending on the settings in the app options. After a simple connection using eyelets to the battery and downloading the new Android or Apple app, the current voltage value can be retrieved. Please note: The transmitter is suitable for 12 V batteries and is only suitable for lithium batteries! The new JMP Skan Monitor 2 requires the new free app "JMP BatteryMonitor II"! Please download the free app from the Apple App Store or Google Play Store under JMP Battery Monitor II. The connection is made via Bluetooth. (Only from Bluetooth 4.0; e.g., from iPhone 4s, iPad3, or iPod Touch 5). The range is approximately 10 meters. Features: The JMP Skan Monitor 2 is excellent for detecting overvoltage > 14.9 V from the alternator before damage to the battery occurs. If the minimum voltage is not met, a reminder for soon recharging the battery is given. Easy attachment using eyelets to the battery. Power consumption is only about 2 mA. No damage occurs to the transmitter or battery in case of reverse polarity. Download the free app from the Apple App Store or Google Play Store under JMP Battery Monitor II. Voltage recording even during rides, results can be sent via email (file display in Excel possible).