The carbon frame cover is attached directly to the frame. It covers the frame and attracts attention. The frame cover is not only convincing visually. Thanks to the high surface quality of Ilmberger Carbon. the frame cover can withstand intensive use over a long period of time. This means that there are no unpleasant work marks on the rough cast surface of the frame either after countless long tours or during daily use of the motorcycle. In order to perfect the high-quality impression. the frame cover not only runs along the vertical frame strut. where the leg rubs. but also extends far upwards. where it disappears under the tight side cover. It is therefore difficult to see from the outside where the frame cover begins and where it ends. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The carbon frame cover is attached directly to the frame. It covers the frame and attracts attention. The frame cover is not only convincing visually. Thanks to the high surface quality of Ilmberger Carbon. the frame cover can withstand intensive use over a long period of time. This means that there are no unpleasant work marks on the rough cast surface of the frame either after countless long tours or during daily use of the motorcycle. In order to perfect the high-quality impression. the frame cover not only runs along the vertical frame strut. where the leg rubs. but also extends far upwards. where it disappears under the tight side cover. It is therefore difficult to see from the outside where the frame cover begins and where it ends. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional matte clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The carbon frame cover is attached directly to the frame. It covers the frame and attracts attention. The frame cover is not only convincing visually. Thanks to the high surface quality of Ilmberger Carbon. the frame cover can withstand intensive use over a long period of time. This means that there are no unpleasant work marks on the rough cast surface of the frame either after countless long tours or during daily use of the motorcycle. In order to perfect the high-quality impression. the frame cover not only runs along the vertical frame strut. where the leg rubs. but also extends far upwards. where it disappears under the tight side cover. It is therefore difficult to see from the outside where the frame cover begins and where it ends. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional matte clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The frame cover left side in carbon with matt finish for the Ducati Panigale V4 R from 2019 is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance

The frame cover right side in carbon with matt finish for the Ducati Panigale V4 R from 2019 is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. the Carbon Framecover weighs about 270 gram

The sprocket cover is one of the most underrated components on the whole motorcycle. Installed centrally on the motorcycle. it surrounds the chain sprocket and does more than it might seem at first glance. It protects the engine and many other components from flying grease while driving. This is particularly stubborn as dirt and difficult to remove from the soft surface of the original part. A hard surface. as it occurs with high-quality carbon. is more suitable here. The component can utilize its full potential not only technically. but also optically. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The sprocket cover is one of the most underrated components on the whole motorcycle. Installed centrally on the motorcycle. it surrounds the chain sprocket and does more than it might seem at first glance. It protects the engine and many other components from flying grease while driving. This is particularly stubborn as dirt and difficult to remove from the soft surface of the original part. A hard surface. as it occurs with high-quality carbon. is more suitable here. The component can utilize its full potential not only technically. but also optically. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional matte clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The front fairing in carbon for the Aprilia RSV 4 (2009-now)is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. This Carbonpart can be supplied for an additional charge of 10% in glossy finish.

The Front Fairing Racing in carbonfiber with gloss finish for the Honda CBR 1000 RR-R/SP MY2020 is a direct replacement for the original component. Racing part - not for use in public road!This front fender contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality

The Front Fairing gloss in carbonfiber for the Panigale V2 is a direct replacement for the original component. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part. The facts:   - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional matte clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The product is in progress - product description and price will follow shortly.

The front fairing for the Ducati Panigale V4 R Racing is delivered in a shiny surface and this stands in contrast to the matt carbon.original Ducati Performance parts. The Ilmberger Carbon fairing top is installed instead of the standard plastic part and is mounted exclusively at standard receiving points. This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The front fairing (lower part) in gloss carbonfiber for the Ducati V4 Streetfighter is a direct replacement for the original component. This front fender contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality

The front fairing (lower part) in matt carbonfiber for the Ducati V4 Streetfighter is a direct replacement for the original component. This front fender contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality

The Front Fairing Racing in carbonfiber with matt finish for the Honda CBR 1000 RR-R/SP MY2020 is a direct replacement for the original component. Racing part - not for use in public road!This front fender contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality

The Front Fairing matt in carbonfiber for the Panigale V2 is a direct replacement for the original component. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part. The facts:   - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional matte clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

In the Stocksport version of the front fairing in gloss finish for the Ducati V4 / V4 S Racing the air intakes are unchanged and it is 100% in accordance with the Stocksport regulations. The high-gloss surface pronounced the sporty character of the Panigale V4 / V4 S Racing.This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

In the Stocksport version of the front fairing in matt finish for the Ducati V4 / V4 S Racing the air intakes are unchanged and it is 100% in accordance with the Stocksport regulations. The matt finish of the surface fits perfectly with the original carbon parts of the Panigale V4 / V4 S Racing.This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The front fairing in carbon for the Ducati models 848/1098/1198 is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The Superbike version of the front fairing in matt finish for the Ducati V4 / V4 S Racing is equipped with extremely optimized air intakes. This change. compared to the original part. supplies the airbox with as much pressure and fresh air as possible. The matt finish of the surface fits perfectly with the original carbon parts of the Panigale V4 / V4 S Racing.This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Our front fender for the Ducati Supersport 939 in gloss finish blends into the motorcycle's overall appearance. This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The mudgard for the Ducati XDiavel 2016 is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. The carbon front mudguard weighs less than 200g and leads to a massive weight saving. compared to the original parts weight of around one pound! Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.