Air Intake (Front Fairing centre piece) BMW S 1000 RR starting from MY 2019 This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. This article uses the rectangle brackets for assembly and is compatible with article IAO.030.S119S.K. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The front fairing center piece in carbon is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Airintake Channel fits to BMW S 1000 RR starting from 2019. and BMW M 1000 RRThis part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Generator cover BMW 4 cylinder models since 2019 This part is a protective carbon piece and is mounted directly on top of the original component. For the mounting only original screwpoints are used. p>   In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly  

The carbon alternator cover for the BMW S 1000 RR Stocksport/Racing (2010-now) with partially attached using the alternator cover screws. and in the front area also glued on using a small dot on the alternator cover. This part is an addition to the original components on the motorcycle and helps to protect the motorcycle. The parts are eighter mounted on original fastening points or glued on the surface with specially delivered glue-strips. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. 

The carbon alternator cover for the BMW S 1000 R (2014-now) / S 1000 RR Street (2010-now) / HP 4 (2012-now) with partially attached using the alternator cover screws. and in the front area also glued on using a small dot on the alternator cover. This part is an addition to the original components on the motorcycle and helps to protect the motorcycle. The parts are eighter mounted on original fastening points or glued on the surface with specially delivered glue-strips. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. 

Original BMW Spare Part Additional Information The part with the BMW part number 51 14 8 164 924 is used on the following vehicles:

Badge Holder left BMW S 1000 RR from MY 2019This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Badge Holder right BMW S 1000 RR starting from MY 2019This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The bellypan of the BMW S1000RR Racing is part of the race fairing kit of the BMW S 1000 RR Racing since 2019. It is mounted via quick fasteners and not compatible with the original fairing parts. It is only compatible with a full racing exhaust system. The lower fairing is closed and is suitable to catch up to 5L of fluids. In the front and the rear are holes which can be open when it’s raining.  A Carbonfairing is the lightest possible way of producing a fairing and protects the parts underneath on an extraordinary high level.    In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight. In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts   - racing part. not for street use - improved cooling capacity for the brake - better protection of the lower fork tubes - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Delivery ready for installation - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

The 1-piece street carbon engine spoiler for the BMW S 1000 RR is made from special high-temperature prepreg carbon material and was designed for use with the original exhaust system (original pre-silencer). mounting the engine spoiler requires the bracket kit item no. VEH.034.S100S.K. This kit contains the required brackets. screws and quick-release fasteners.Combined with the trim insert MSE.035.S100S.K the engine spoiler can also certainly be mounted to a Racing complete system. In this case the trim insert closes the gap resulting from the omission of the original pre-silencer. This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. This bellypan can be fitted together with the original exhaust system. It is developed to cover the original muffler under the engine. Please order also the holderkit VEH.034.S100S.K to mount this bellypan. This kit includes the holders. screws. and fasteners to mount the bellypan. Together with the Inlay MSE.035.S100S.K the bellypan is also very good to use it with a full racing exhaust. This inlay closes the gap in the rear bottom of the bellypan if the original muffler unter the engine is not mounted anymore.

The 1-piece street carbon engine spoiler for the BMW S 1000 RR (2017 ) is made from special high-temperature prepreg carbon material and was designed for use with the original exhaust system. as well as with full racing exhaust systems. Our bellypan is longer than the original part and it covers the pre-exhaust. Please note that you need our fairing holder kit VEH.203.S117S.K for mounting the longer bellypan.This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.  

The rear fairing for biposto riding. surrounds the pillion seat and allows a sporty look of the motorcycle even in operation with two persons. In combination with the SIA.009.M123S.K and the RHA. 011.M123S.K. the entire rear can thus be wrapped in carbon. while not excluding the eventual operation with a passenger.  If the motorcycle is to be returned even closer to its origins on the racetrack. the Monoposto rear fairing is the one to choose.    For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight. In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts   - with German ABE - quick change between solo ride and ride with a passenger - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional glossy clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

BMW S1000R S 1000 R S1000RR S 1000 RR road from Bj. 2015 Carbon frame rear trim tail section below  The lower seat / rear frame Guards Carbon for BMW S 1000 R / S 1000 RR road (from 2015) replaces the original part using the original mounting points. In the foreground weight savings are (usually savings of approximately 70% compared with the original component) and higher carbon Steifigkeit.Das part was completely in accordance with the latest guidelines in the autoclave prepreg (see FAQ) material and in the next step, as with us usual, for protection against environmental influences with a clear plastic coating überzogen.Diese plastic coating exceeds the usual clear lacquer coating enormously in the protective effect, scratch resistance and durability. But not only technically can score the coating, but also highlights the three-dimensional effect of the carbon structure again deutlich.Weitere features and details of the production of our Carbon Parts Please refer to our website under the tab quality.

BMW S1000RR S 1000 RR Superstock / Racing from Bj. 2010 Carbon crash pad on the frame right The crash pad on the upper Motorverschraubung offer the very vulnerable from falls field the best possible protection. In the area at the most vulnerable location on the motor mounting screw is for additional protection in the interior of the carbon member is a rotary part made of aluminum eingearbeitet.Der crashpad the frame complements the vehicle and provides additional protection for the vehicle against damage. The somewhat vulnerable when falling upper Motorverschraubung is extremely effective protected by the Mantle. The assembly of the parts is done via supplied tape and / or the use of original mounting points. The Crash Pad is intended only for the racing operation. The carbon part is according to the latest guidelines in the autoclave entirely of prepreg (see FAQ) material and in the next step, as usual with us, covered for protection against environmental influences with a clear plastic coating. This plastic coating exceeds the usual clear lacquer coating in the protection, scratch resistance and resistance enormous. But not only technically can score the coating, but also highlights the three-dimensional effect of the carbon structure still further.

Whether alone or with a passenger - the middle part of the tail fairing forms the basis for all the fairing parts above it. The unpainted plastic is replaced, enhancing the rear in all combinations of high quality. For our carbon, we exclusively use prepreg fabric produced specifically for this purpose, which is also used in a similar form in Formula 1 and aerospace. The material, laminated by hand with great care and cured in several stages in an autoclave, impresses not only with its unique appearance but also with its exceptional technical properties. It has three times the specific stiffness of steel at the same volume and, due to its particularly low density, weighs only a fraction of that. These properties are particularly pronounced in our product due to the high fiber volume content. To optimally protect this high-quality material from environmental influences of all kinds, we, as the only carbon manufacturer worldwide, use a specially developed plastic coating on all surfaces. This, in combination with our clear coat, provides an unprecedented and unique depth effect that highlights the high quality of the material. So that not only riding but also working on it is a pleasure, we use only the original mounting points for this part. The facts: - with ABE – no additional registration required - only for solo operation - Sealing of all surfaces (inside and outside) with a unique plastic coating for protection against environmental influences of all kinds - additional glossy clear coat on all visible surfaces - optimally protected against UV light - delivered in ready-to-install condition - TÜV certified quality - made from prepreg material specially produced for Ilmberger - manufactured in-house according to ISO 9001 - installation using the original mounting points - quick and easy assembly

Rear fender Racing suitable for BMW S 1000 RR from model year 2019 and M 1000 RR Our carbon part replaces the original component using the original mounting points. The focus is on weight savings (typically a reduction of about 70% compared to the original component) and increased stiffness. The carbon part has been completely manufactured from prepreg material (see FAQ) in an autoclave according to the latest guidelines and, as is customary with us, coated with a clear plastic layer for protection against environmental influences. This plastic coating significantly outperforms the usual clear lacquer coating in terms of protective effect, scratch resistance, and durability. But not only does the coating excel technically, it also emphasizes the three-dimensional effect of the carbon structure even more clearly.

Clutch cover BMW S 1000 RR Street 2019 This part is a protective carbon piece and is mounted directly on top of the original component. For the mounting only original screwpoints are used. The part comes in a very durable version and not only protects the original cover. but also. due to its unique shape. the endangered clutch release bearing on the bottom of the cover.   In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly  

Clutch Cover BMW S1000 RR Stocksport from 2017 Racingpart no Tüv or ABE The clutch cover in Carbon for the BMW S 1000 RR Stocksport is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. Picture similar

The carbon clutch cover for the BMW S 1000 RR Stocksport/Racing (2010-now) is glued to the original clutch cover. This part is an addition to the original components on the motorcycle and helps to protect the motorcycle. The parts are eighter mounted on original fastening points or glued on the surface with specially delivered glue-strips. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. 

Please have a look at the 360 ° Video with the crashpads on the Frame for BMW S 1000 RR / HP 4. - The crashpad on the frame is covering the important area around the upper engine holder. The crashpad on the frame is an addition to the original components on the motorcycle and helps to protect the motorcycle. This crashpad protects the upper engineholder. The parts are eighter mounted on original fastening points or glued on the surface with specially delivered glue-strips. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Please have a look on the 360 ° Video with the crahpads in carbon for the BMW S 1000 RR (all MY) and HP 4. You will find the Video at the button Product Videos above this description. - The crashpad on the frame is covering the important area around the upper engine holder.  The crashpad on the frame is an addition to the original components on the motorcycle and helps to protect the motorcycle. This crashpad protects the upper engineholder. The parts are eighter mounted on original fastening points or glued on the surface with specially delivered glue-strips. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

Electrical cable cover BMW S 1000 RR starting from MY 2019 In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly

Fairing Holder (4 pieces) kit needed for race fairing kit for BMW S 1000 RR 2019. and BMW M 1000 RR.This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.