Our cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of up to 4.5 cm. This means that some shafts are up to 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

JMP Exhaust Clamp - Diameter 38 mm- Width 20 mm- Chrome-plated- Clamping range 36-39mm Technical Data:Type: Exhaust Pipe Clamps (Motorcycle) Min Clamping Range: 36.0 mmMax Clamping Range: 39.0 mmWidth: 20.0 mmMaterial: Steel Color: chrome Special Feature: chrome-plated

Fork Tubes by JMP   - made from high-quality raw materials - special chrome coating with low breakaway torque - each fork tube undergoes a quality inspection before delivery - manufactured on state-of-the-art CNC machines in Central EuropeTechnical Data:Upside down:   No Outer diameter:   41 mmInner diameter:   33 mmLength:   652 mmTop connection:   No thread Bottom connection:   No thread Color:   chrome

Fork Tubes by JMP   - made from high-quality raw materials - special chrome coating with low breakaway torque - each fork tube undergoes a quality inspection before delivery - manufactured on state-of-the-art CNC machines in Central EuropeTechnical Data:Upside down:   No Outer diameter:   41.3 mmInner diameter:   35 mmLength:   607 mmTop connection:   Snap ring Bottom connection:   No thread Color:   chrome

Vehicle-Specific Information: BMW has delivered 2 different versions of this standpipe under the identical original number: with and without thread at the top. This item is the version without thread at the top.Fork Standpipes from JMP - made from high-quality raw materials - special chrome coating with low breakaway torque - each standpipe undergoes a quality inspection before delivery - manufactured on state-of-the-art CNC machines in Central EuropeTechnical Data:Upside down: No Outer Diameter: 38.5 mmInner Diameter: 31 mmLength: 561 mmTop Connection: Internal Thread Bottom Connection: No Thread Color: chrome

Fehling Chopper and Touring Handlebars Type: LN 12 - made of chrome-plated steel tube - tube diameter 22 mm (7/8´´) - without cable drilling - with TÜV certificate - compatible with Suzuki GS 450 T, GR 650; Kawasaki Z 1100 ST; BMW R 45/65 (6 cm wider than original). Fehling has been manufacturing accessories for motorcycles and large scooters since the 1950s. From development to production, top quality according to ISO 9001 and Made in Germany. Dimensions: a: 745 mm b: 235 mm c: 165 mm d: 220 mm e: 250 mm Technical Data:Diameter: 22.2 mm (7/8 inch) Type: Chopper Touring Material: Steel Width: 745 mmColor: chrome Special Feature: no special feature Manufacturer: Fehling

Fehling Touring Handlebar Type: LN 1   - made of chrome-plated steel tube - tube diameter 22 mm (7/8´´) - without cable drilling - with TÜV certificate- like BMW /5 models   Fehling has been manufacturing accessories for motorcycles and large scooters since the 1950s. From development to production, top quality according to ISO 9001 and Made in Germany.   Dimensions: a: 650 mm b: 60 mm c: 70 mm d: 55 mm e: 200 mm

Fehling Touring Handlebar Type: LN 4 - made of chrome-plated steel tube - tube diameter 22 mm (7/8´´) - without cable drilling - with TÜV certificate - for BMW/6 models Fehling has been manufacturing accessories for motorcycles and large scooters since the 1950s. From development to production, top quality according to ISO 9001 and Made in Germany. Dimensions: a: 660 mm b: 105 mm c: 105 mm d: 110 mm e: 200 mm Technical Data:Diameter: 22.2 mm (7/8 inch) Type: Touring Material: Steel Width: 660 mmColor: chrome Special Feature: no special feature Manufacturer: Fehling

TRW Mystic Handlebar "High Chrome"   made of chrome-plated steel tube tube diameter 22 mm 3-layer special coating against corrosion no dull chrome spots at the bending points attractive design for a stylish appearance good steering behavior due to well-developed shapes with parts certificate   Dimensions: a: 905 mm b: 130 mm c: 240 mm d: 130 mm e: 280 mm   Please use our attached PDF to check for an ABE for your vehicle. If your model is not listed in the ABE list, please use the parts certificate for an entry. Technical Data:Diameter:   22.2 mm (7/8 inch) Type:   Chopper Material:   Steel Width:   905 mmColor:   chrome Special Feature:   none Manufacturer:   TRW

Choke Screw CV Carburetor

Clip spring for float needle Bing constant pressure carburetor type 64-3.

Clip Temperature Sensor

Closure Screw JMP   - M18X1.5X12- DIN 908- Zinc-platedTechnical Data:Type:   Oil Drain Screws    Closure Screws Thread:   M18 x 1.5 Diameter:   18 mmLength:   12 mmHead:   Flat Head Drive:   Internal Hexagon Surface:   Electro-galvanized Material:   Steel Color:   Silver DIN:   908 O-ring/Washers:   None Manufacturer:   JMP Bolt For Safety Wire:   No Technical Data:Thread:   M18 x 1.5 Length:   12 mmHead:   Round Head with Internal Hexagon Material:   Steel Color:   Gray For Safety Wire:   No O-ring/Washers:   No Magnetic:   No

Clutch Bolt Stainless Steel   - Total Length: 98.5mm - Diameter: 8mm

Our cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of a maximum of 4.5 cm. This means that some shafts are up to a maximum of 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.Technical Data:Cable:   1386 mm

n.v.

n.v.

Vehicle-Specific Information: for vehicles with high handlebars

Our cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of up to 4.5 cm. This means that some shafts are up to 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Vehicle-Specific Information: High HandlebarOur cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides permanent lubrication and does not dry out. The shafts glide in a durable calcium grease.

Clutch Friction Plate Note: 6 pieces are required.

Clutch Lever | Design '2stripes' Motorcycle lever adjustable in 6 stages. Wide grip area. Black lever with fine contrast cut. Adjuster available in many modern colors. Can be adjusted with one hand while riding. Perfect ergonomics and fine grip feel. High-strength CNC-machined aluminum. With ABE (General Operating Permit). NOTE Since our levers are individually assembled according to customer specifications and model-specific, they are excluded from cancellation.

This is a new part with storage marks Vehicle: R18 Manufacturer: BMW Condition: Like new with storage marks Description: sold as shown Part number: 32729443823

This is a new part with storage marks Vehicle: R18 Manufacturer: BMW Condition: Like new with storage marks Description: sold as shown Part number: 32729443823