Ignition Coil Bosch

Bosch Multifunction Relay / Load Relay 5-pin, 12 V Mini relay without holder and diode, with resistor Technical Data: Rated current: 30 A Rated voltage: 12 V Number of poles: 5-pole Relay function: Load contact Temperature range from: -40 °C Temperature range up to: 85 °C Housing type: Plastic housing Protection class: IP5K4 (housing) / IP20 (connector) Resistance: 90 Ohm Dimensions (LxWxH): 281 x 281 x 368.5 mm Technical Data:Voltage: 12 VNumber of poles: 5 Switch function: Normally open Load capacity: 30 AWith holder: No

Nut

Bracket for BMW Original Headlight for BMW R 1200/1250 GS LC (2013-) for Combination with Hepco&Becker Tank Protection Bars in combination with Hepco&Becker tank protection bars original BMW auxiliary headlight not included in the delivery special bracket for the original BMW auxiliary headlights

Brake Caliper Piston Repair Kit 38mm For models with dual disc.

Brake Caliper Piston Repair Kit

Brake Caliper Repair Kit 40mm

Vehicle-Specific Information: Attention: Only suitable for vehicles with ATE brake caliper Brake Caliper Repair Kit

Brake Caliper Repair Kit ATE 38mm

Brake Caliper ScrewTechnical Data:Type: Threaded Screws Thread: M10 x 1.5 Length: 25 mmHead: Cylinder Head Drive: Internal Hexagon Surface: No Finishing Material: Stainless Steel Color: Silver Grade: 8.8 O-Ring/Washers: None Manufacturer: Other For Safety Wire: No

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm.Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silver All items have been mounted and tested on original motorcycles - without any modifications.

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm. Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silverAll items have been mounted and tested on original motorcycles - without any modifications.

The brake lever cap increases the reachable area of the foot brake and extends it by 15 mm. It is suitable for brake levers with a round body of Ø 17 mm.Easy installation. Simply slide on and tighten the set screw.Length approx. 6.5 cm, inner Ø 17 mmColor silverAll items have been mounted and tested on original motorcycles - without any modifications.

Brake light switch / Clutch switch

Brake Light Switch Original Spare Part

Guide Pin Set Brembo Brake Caliper Attention: The middle guide pin has a length of 24.6mm.

This is a new part offered Vehicle: R1200GS LC + Adventure LC Manufacturer: BMW Condition: New with storage marks Description: sold as shown Part number: 34118405105

This is a new part offered Vehicle: R18 Manufacturer: BMW Condition: New Description: sold as shown Part number: 34119444024 Fits the following vehicles:

Vehicle-Specific Information:  for single discSV - Friction Material CompositionFull metallic sintered material with special coating.High friction coefficient ensures very good performance.Can be used on almost all discs.Only in exchange for sintered pads in the original equipment.Only conditionally suitable for racing, as there is no heat resistance above 400 degrees.Only suitable for the front axle. Restriction BMW, brake pads for BMW R65 from 85-93 with a brake disc

The carbon brake pipe cover for the BMW R 1200 GS (2004-2012) / HP 2 Megamoto (2008-2013) / HP 2 Sport (2008-2012) / R 1200 S (2006-2008) / R 1200 R (2007-2014) / R Nine T models greatly highlights and adds to the motorcycle&rsquos sporty styling. Certain details simply perfect a motorcycle! This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

EBC BRAKE SHOES Made from aluminum using high-pressure injection molding and equipped with asbestos-free premium linings in standard designTechnical Data:Diameter:   200 mmWidth:   30 mmGrooved:   No Includes Springs:   No Manufacturer:   EBC

Standard lining.Technical Data:Diameter:   200 mmWidth:   30 mmGrooved:   No Includes Springs:   No Manufacturer:   TRW

Brake-pipe Cover Carbon - BMW R 1250 GS from 2019 for the individual style of the bike  This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.

The carbon brake pipe cover highlights the motorcycle&rsquos sporty styling and rounds off e.g. a motorcycle with carbon rear hugger. Certain details simply perfect a motorcycle! The brake pipe cover in carbon for the BMW R 1200 GS models is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.