Progressively wound fork springs from YSS in a firmer design than the original. The YSS fork springs are made from high-quality silicon spring steel. This allows for a reduction in wire thickness, making the spring more active and slimmer, while effectively preventing torsion of the spring.To minimize noise and improve oil flow in the fork, the springs are fully polished and ground at both the top and bottom.The delivery includes 2 springs for a complete fork conversion.Technical Data:Spring Type:   Progressive Length:   530 mmDiameter 1:   33.5 mmSpring Rate 1:   6.5 N/mmSpring Rate 2:   8.5 N/mmAir Chamber Left:   170 mmAir Chamber Right:   170 mmRecommended Viscosity:   15W Manufacturer:   YSS

Vehicle-Specific Information:  with Anti Shudder ClipStandard Pad Organic with ceramic underlayer for thermal insulation. Anti-corrosion coating, high durability. Compatible with all discs. Solid braking performance, good wet braking behavior. Suitable for front and rear axle.

  Brembo brake discs EBC. MADE IN UK. The goal in development is to improve braking performance compared to the original brake disc. EBC uses HPSR steel with a low carbon content, which has an 18% higher coefficient of friction. This steel is significantly more resistant to rust than cast steel. Additionally, the entire surface is protected with a 3-micron thick zinc coating, which wears off in the brake pad contact zone during the bedding-in process. Only in this area can light surface rust form after prolonged periods of inactivity.   The brake discs are drilled in a bird wing design to minimize the number of holes while optimizing the cleaning of the brake disc from rainwater and brake dust. The fewer holes there are, the better the wet braking performance and the lower the wear.   - Rigid brake disc. - Made from rolled HPSR steel with low carbon content. - Brake surface drilled with an optimized hole pattern. - Radially ground. - Galvanized for corrosion protection. - EBC recommends EBC Organic brake pads or for sporty riders EBC Double-H sintered brake pads. - Standalone design.      Technical Data:Outer Diameter:   285 mmInner Diameter:   51.2 mmBolt Circle:   68 mmNumber of Holes:   2    4 Hole Diameter:   4 mmThickness:   4.7 mmOffset:   15 mmDesign:   floating Manufacturer:   EBC

Vehicle Specific Information:  Cast wheel 3 spokes front right up to 10/89Quality ball bearings from NTN.Technical Data:Design:   Deep groove ball bearing Type:   63005 Inner Diameter:   25.00 mmOuter Diameter:   47.00 mmWidth:   16.00 mmSealing:   2 sealing discs Bearing Clearance:   Standard

Used part, normal signs of use, see additional pictures BMW part number: 63231459096 Fits according to part number for the following vehicles: K589 K 1100 LT K589 K 100 LT 87 K589 K 100 RT 84 K569 K 75 RT

BMW Original Spare Part Air Filter Insert Top Brand Quality

BMW Original Spare Part Air Filter Insert Top Brand Quality

Used part, normal signs of use, Scratches, see additional pictures BMW part number: 46632307924 Fits the following vehicles according to part number:

This is a used part being offered Vehicle: K1200LT Manufacturer: BMW Condition: noticeable signs of use Description: sold as shown Part number: 11781742051

Used part, normal signs of use, see additional pictures BMW part number: 46712332733 Fits the following vehicles according to part number:

BMW Original Front Brake Disc with Rivets NEW Product Description This offer includes 1 front brake disc D=320-5.0MM . This offer applies to the item in the red marked circle!!! ( Illustration No. 1 ) BMW Part Number: 34117711429 Fits according to part number for the following vehicles: K 1200 S K 1300 S K 1200 GT K 1300 GT

With the robust inner bags, loading and unloading is simple and convenient. The fit is optimally tailored to the cases, and small parts can be stored in the outer pockets – made of genuine leather on the sides. Comes with a shoulder strap. High-quality inner bag made of durable polyester-cotton fabric Perfectly designed for standard cases with a volume of 37 l Attached outer pockets made of genuine leather with magnetic closure, on both sides Additional zippered outer pocket for small parts Main compartment easily accessible via a long, double zipper Practical mesh pocket in the lid Light-colored lining for better visibility Stable bottom for good standing Shoulder strap with BMW Motorrad lettering 2 valuable metal labels with BMW Motorrad lettering and BMW logo Color: Black Additional Information Contents: 1 piece. Can be used on the right or left side.

BMW Original Spare Part Air Filter Insert Top Brand Quality

Wasserdichte Tanktasche Volumen ca. 10 l + 2 l Erweiterungsmöglichkeit Volumenverstellung über einen umlaufenden Reißverschluss Kleines Sichtfach mit Einlegeboden 2 Außentaschen sowie 1 Innentasche für Kleinteile Längenverstellbarer, abnehmbarer Schultergurt Tragegriff am vorderen Teil der Tasche Farbe: Schwarz Material: Obermaterial aus hochwertig gewebtem Polyester; Exakt angepasster EVA-Boden mit rutschhemmender Beschichtung

BMW Original Spare Part Air Filter Insert Top Brand Quality

Vehicle-Specific Information: for left sideEBC Prolite brake disc floating, Full Floater. MADE IN UK. The goal in development is to improve braking performance compared to the original brake disc. EBC uses HPSR steel with a low carbon content, which has an 18% higher coefficient of friction. This steel is significantly more resistant to rust than cast steel. Additionally, the entire surface is protected with a 3-micron thick zinc layer, which wears off in the brake pad contact zone during the bedding-in process. Only in this area can light surface rust form after prolonged periods of inactivity.   The brake discs are drilled in a bird wing design to minimize the number of holes while optimizing the cleaning of the brake disc from rainwater and brake dust. The fewer holes there are, the better the wet braking performance and the lower the wear.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus the coefficient of friction remains constant. - Braking surface drilled with an optimized hole pattern. - Galvanized for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - Independent design.Technical Data:Outer Diameter: 285 mmInner Diameter: 62.2 mmBolt Circle: 80 mmNumber of Holes: 4 Hole Diameter: 10.5 mmThickness: 4.7 mmOffset: 31.5 mmDesign: floating Manufacturer: EBC

Vehicle-Specific Information: High HandlebarOur cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of a maximum of 4.5 cm. This means that some shafts are up to a maximum of 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Progressively wound fork springs from YSS in a firmer design than the original. The YSS fork springs are made from high-quality silicon spring steel. This allows for a reduction in wire thickness, making the spring more active and slimmer, while effectively preventing torsion of the spring.To minimize noise and improve oil flow in the fork, the springs are fully polished and ground at both the top and bottom.The delivery includes 2 springs for a complete fork conversion.Technical Data:Spring Type: Progressive Length: 560 mmDiameter 1: 32 mmSpring Rate 1: 5.7 N/mmSpring Rate 2: 8.7 N/mmAir Chamber Left: 170 mmAir Chamber Right: 170 mmRecommended Viscosity: 15W Manufacturer: YSS

Product Description: original BMW workshop equipment Contents 50 ml 29.49 €/100 ml (base price indication according to §2 German Price Indication Regulation (PAngV) for sales in Germany) Safety data sheet available upon request May cause allergic reactions For professional users only

BMW Lubricant Grease Straburags for Cardan Footpeg Joints Shift Parts Product Description: original BMW workshop equipment has been used for many years for e.g. cardan shafts, plug connections, joints strongly adhesive good corrosion protection prevents tribocorrosion (combined effect of corrosion and wear) water-resistant - even under outdoor conditions approved by Knorr Brake N (12006-1.23 product info available) safety data sheet available upon request contains Pin-2(3)-enes. May cause allergic reactions content 50g 39.90 €/100g (basic price indication according to §2 German Price Indication Regulation (PAngV) for sale in Germany)

Product Details Article Number: 2414856 You get the power! With the dual USB charger, you can charge two mobile devices simultaneously while riding through the 12V socket – whether it's a smartphone, mobile phone, MP3 player, tablet, or digital camera. The automatic detection of charging technology for all common smartphones allows for super-fast charging with a maximum charging current of up to 2 x 2 Amperes. Charger for simultaneous charging of up to 2 mobile devices while riding through the motorcycle's 12V socket Compatible with smartphones, mobile phones, tablets, MP3 players, digital cameras, etc. 2 USB ports (5V / max. 2A each), splash-proof Charging plug suitable for all BMW motorcycle sockets Cable length: 120 cm Charging plug and cable waterproof according to IP67 LED power display Automatic detection of charging technology for all common smartphones to utilize the maximum possible charging current Thermal fuse against overheating Input voltage: 12V DC Output voltage: 5V (per USB port) Charging current: max. 2A (per USB port) Connection (output): 2x USB port Weight (including packaging): approx. 140g Certification: CE, FCC, CCC Branding with BMW Motorrad lettering Color: Black

Product Details Article Number: 2414856 You get the power! With the dual USB charger, you can charge two mobile devices simultaneously via the 12V socket while riding – whether it's a smartphone, mobile phone, MP3 player, tablet, or digital camera. The automatic detection of charging technology for all common smartphones enables super-fast charging with a maximum charging current of up to 2 x 2 Amperes. Charger for simultaneous charging of up to 2 mobile devices while riding via the motorcycle's 12V socket Compatible with smartphones, mobile phones, tablets, MP3 players, digital cameras, etc. 2 USB ports (5V / max. 2A each), splash-proof Charging plug suitable for all BMW motorcycle sockets Cable length: 60 cm Charging plug and cable waterproof according to IP67 LED power display Automatic detection of charging technology for all common smartphones to utilize the maximum possible charging current Thermal fuse against overheating Input voltage: 12V DC Output voltage: 5V (per USB port) Charging current: max. 2A (per USB port) Connection (output): 2x USB port Weight (including packaging): approx. 140g Certification: CE, FCC, CCC Branding with BMW Motorrad lettering Color: Black

BMW Motorrad Protective Glass for 10-Inch TFT Display for example R18B K1600GT GTL from 2022 The protective glass for the 10-inch TFT display is hardened and non-reflective. It protects the display without impairing readability and is easy to install. High-quality, hardened glass, scratch-resistant and non-reflective. Reduces the formation of water spots on the display. Easy bubble-free application thanks to the installation kit and silicone coating on the underside. Secure protection of the TFT display against scratches and similar damage. Does not impair the readability of the display.

Artikelnummer: 76 61 5 A82 572Praktischer Schlüsselanhänger mit Make Life a Ride Schriftzug und großem, eingewebtem BMW Motorrad Schriftzug.ProdukthighlightsKleiner Make Life a Ride SchriftzugGroßer BMW Motorrad SchriftzugEckdatenMaterial: 100 % Baumwolle