Vehicle-Specific Information: for ATE CaliperStandard Pad Organic with ceramic underlayer for thermal insulation. Anti-corrosion coating, high durability. Compatible with all discs. Solid braking performance, good wet braking behavior. Suitable for front and rear axle.

EBC Prolite Brake Disc, Full Floater   EBC replaces the rigid original disc with a Full Floater brake disc. The manufacturing of the complex and expensive Full Floater offers significant advantages when braking. The brake ring, sawed, drilled, and ground from forged HPSR steel bars, can expand freely even during repeated hard braking, such as when descending mountain passes, without deforming. Here, the low carbon content of the used HPSR steel proves beneficial, as it ensures minimal microstructural changes in the steel under the thermal stress of heating and cooling the brake disc in demanding road conditions. An EBC Full Floater brake disc is always a significant gain in safety.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus maintaining a constant coefficient of friction. - Braking surface drilled with an optimized hole pattern. - Zinc-coated for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - EBC recommends EBC Double-H sintered brake pads for optimal braking performance. - Independent design.Technical Data:Outer Diameter:   260 mmInner Diameter:   62.2 mmBolt Circle:   79 mmNumber of Holes:   5 Hole Diameter:   8.5 mmThickness:   4.7 mmOffset:   47.8 mmDesign:   floating Manufacturer:   EBC

Fuel Tank Seal

Fuel Tap

Fuel Tap

Fuel Tap Seal Germa 7-Hole

Fuel Tap Seal Karcoma 5-Hole

Cable only suitable for connection to a car ZA socket. "Voltage converter" plug cannot be cut off!!Note: For devices with a power consumption > 2 Amperes.

Throttle slide spring for Bing constant vacuum carburetor type 64-3. Total length 119 mm; Outer diameter 24 mm; Wire thickness 0.8 mm Spring: soft - Replacement part for Bing carburetors: 64/26/303-30464/26/315-31864/28/303-30464/32/305-30664/32/311-31464/32/323-32464/32/335-336 (BMW R65US)64/32/347-35264/32/375+377+379+381+383+385

SACHS cover for the clutch Druckplatte- OE -

optionaler Gepäckhaken für den GOBI SeitenkofferLieferumfang: 1 Stück inkl. Schraubenwird mit dem Deckel verschraubt

Gasgriff mit Verzahnung Neu für BMW R 54 65 80 100 K75 K100Angeboten wird hier ein Gebrauchtteil Fahrzeug: R45, R60/6, R75/6, R90/6, R90S, R45, R45/N, R45T, R45T/N, R65, R65LS, R65T, R60/7, R75/7, R80RT, R80/7, R65GS, R80G/S, R80ST, R80, R80GS, R80GS PD, R100GS, R100GS PD, R100/7, R100T, R100/7T, R100CS, R100RS, R100RT, K100RS, K75, K75S, K75C, K75RT Hersteller: BMW Zustand: NEU, keine Gebrauchsspuren Beschreibung: wird verkauft wie abgebildet Teilenummer: 32721454129, 32721237884

HATTECH STAINLESS STEEL Exhaust System WITHOUT Interference Pipe for BMW R 45 65 + LS `78 - `84 with 35mm Header STAINLESS STEEL - Exhaust System for BMW R 45, R 65, R 65LS `78 - `84: HATTECH STAINLESS STEEL 35mm Header compatible with mufflers with 35mm connection no further modifications necessary Exhaust System - WITHOUT Interference PipeAvailable in various surface finishes: surface untreated / not shortened brushed polished brushed & heat-colored at the welds

Specific backrest for your Hepco & Becker Topcase. The ideal addition for riding with a passenger. The backrest should be a constant companion on every trip with a passenger. The backrest is easily attached to the Topcase. To do this, holes need to be drilled into the Topcase. But don't worry, the installation is simple.The Topcase is 100% waterproof again after the backrest is installed. The backrest is custom-made for each Topcase from black PU material, ensuring a perfect fit and shape.

Specific backrest for your Hepco & Becker Topcase. The ideal addition for riding with a passenger. The backrest should be a constant companion on every trip with a passenger. The backrest is simply attached to the Topcase. For this, holes need to be drilled into the Topcase. But don't worry, the installation is easy.The Topcase is 100% waterproof again after the backrest is installed. The backrest is custom-made for each Topcase from black PU material, ensuring a perfect fit and shape.

Proven Tube Luggage Racks Topcase Carriers for Hepco&Becker Topcases in the highest quality. Hepco&Becker luggage racks are specifically designed for almost all of our topcases. But not only new topcases fit. Older Hepco&Becker models can also be mounted. The base mount has not changed.Not compatible are: Hepco&Becker Orbit Topcase and topcases with universal plate.The carriers are model-specific and fit only the motorcycle listed in the installation instructions. Thanks to the construction from German quality steel, Hepco&Becker luggage racks ensure maximum strength and very high safety. With the high-quality coating and proper care, the look is also maintained in the long term. If necessary, soft luggage can also be secured without any problems. The tube luggage rack offers many possibilities. If space is insufficient, the rack can be combined with the Hepco&Becker universal luggage rack extension. Recommended load: 5kg (Please note the model-specific instructions for each carrier, as well as the motorcycle manufacturer's specifications. Heavy luggage should generally not be transported in the topcase, but in the side cases or tank bag. usually combinable without problems with side case carriers or C-Bow holders (please refer to the installation instructions) including mounting materials and instructions MADE IN GERMANY the topcase is pushed onto the tube luggage rack and locked with a metal locking mechanism on the carrier Luggage racks generally do not require ABE or registration Vehicle-specific notes: Single luggage rack is not combinable with the side case carrier. Fits for: BMW R 65 from model year 1986/ R 80 RT from model year 1985/R100RS/RT (1986-1995)

The Hepco&Becker complete carrier, consisting of side case carriers and a tubular luggage bridge, is securely bolted to the motorcycle and can be only assembled together. This carrier allows for the mounting of nearly all Hepco&Becker side cases. Almost all top cases from our range can be mounted on the tubular luggage bridge. (The Orbit top case, as well as top cases with a universal plastic plate, do not fit)The side cases are locked to the carrier using a locking mechanism. The required lock adapters, which are bolted to the right and left of the side case carrier, are included as standard in the case set (Article number lock adapter: 700114)The model-specific and solidly constructed carriers are perfectly adapted to the respective motorcycle and reinforced at heavily stressed points with special inner tubes. Construction from steel tube Made in Germany firmly bolted to the motorcycle can only be assembled together suitable for almost all Hepco&Becker side cases and top cases Restrictions can be found in the model-specific notes or the assembly instructions Recommended load: 10kg per side case / 5kg in the top case (please observe vehicle-specific notes, our assembly instructions, as well as motorcycle manufacturer specifications) Scope of delivery: right carrier, left carrier, tubular luggage bridge for the rear, mounting materials, and instructions Luggage carriers do not require ABE and are registration-free Vehicle-specific notes: For models with two shock absorbers.

The Hepco&Becker complete carrier, consisting of side case carriers and a tubular luggage bridge, is securely bolted to the motorcycle and can be only assembled together. This carrier allows for the mounting of nearly all Hepco&Becker side cases. Almost all top cases from our range can be mounted on the tubular luggage bridge. (The Orbit top case, as well as top cases with a universal plastic plate, do not fit)The side cases are locked to the carrier using a locking mechanism. The required lock adapters, which are bolted to the right and left of the side case carrier, are included as standard in the case set (Article number lock adapter: 700114)The model-specific and solidly constructed carriers are perfectly adapted to the respective motorcycle and reinforced at heavily stressed points with special inner tubes. Construction from steel tube Made in Germany firmly bolted to the motorcycle can only be assembled together suitable for almost all Hepco&Becker side cases and top cases Restrictions can be found in the model-specific notes or the assembly instructions Recommended load: 10kg per side case / 5kg in the top case (please observe vehicle-specific notes, our assembly instructions, and motorcycle manufacturer specifications) Scope of delivery: right carrier, left carrier, tubular luggage bridge for the rear, mounting materials, and instructions Luggage carriers do not require ABE and are registration-free Vehicle-specific notes: For models with central spring strut. Indicators remain in original position. Suitable for: BMW R 65 from model year 1986 / R 80 RT from model year 1985 / R100RS/RT (1986-1995)

To keep things organized in the case. With this Hepco&Becker inner bag, items no longer lie loose in the case. The case is easier to load since the inner bag can be packed beforehand.And at the end of the tour, you don’t have to remove and carry the entire case, just the inner bag. The bag is made of durable black fabric.Equipped with a 2-way zipper and an adjustable carrying strap,you will always look neat when unpacking with this bag. Delivery includes: 1x inner bag

To keep things organized in the case. With this Hepco&Becker inner bag, items no longer lie loose in the case. The case is easier to load since the inner bag can be packed beforehand.And at the end of the tour, you don’t have to remove and carry the entire case, just the inner bag. The bag is made of durable black fabric.Equipped with a 2-way zipper and an adjustable carrying strap,you will always look neat when unpacking with this bag. Delivery includes: 1x inner bag

compatible with most Hepco&Becker side case carriers. (Please note any potential restrictions in the model-specific notes of the carrier) suitable for one helmet and more includes key and locking cylinder includes lock adapter to secure the case to the side case carrier waterproof thanks to special sealing cover is screwed on and can be painted in vehicle color if needed integrated bumper protects against minor bumps case shell made of impact-resistant, molded plastic cases can be keyed alike to existing cases or top cases.Please enter the key number in the comments field during the ordering process. Scope of delivery: right side case + left side case + 2x lock adapters optional inner bags available in the accessory program Recommended load: 10kg per side case (Please note the model-specific notes of the respective carrier, as well as the motorcycle manufacturer-specific information)

The special Journey Topcase 30 is delivered with a universal mounting plate and installation accessories. This allows for attachment to almost any third-party luggage rack with a flat mounting surface, for which we do not offer a model-specific top case rack. not compatible with Hepco&Becker tube luggage racks, Alurack luggage racks, or Easyrack luggage racks waterproof case shell made of impact-resistant plastic includes universal mounting plate and installation materials includes key and lock cylinder extensive range of accessories available suitable for one helmet Recommended load: 3-5kg in the top case (Please note the model-specific instructions for each rack, as well as the motorcycle manufacturer's specifications. Heavy luggage should generally not be transported in the top case, but in the side cases or tank bag.

Compatible with the model-specific HEPCO&BECKER Lock it tank rings, this everyday little helper can be mounted on all models with a compatible fuel cap.The principle of operation of the tank ring closure: The problems of placing tank bags are eliminated by magnetic centering. The handling is simple and quick. The system is mechanically secured by ribs attached to the sides of the magnets. The transfer forces of the holder amount to over 70kg of vertical load, ensuring a stable and secure connection to the motorcycle at all times. To unlock, simply pull on the holding strap, allowing the magnets to release the system. The magnets align themselves, and the tank bag can be removed.Child's play and effective – simply genius. Compatible with the product family of Royster side bags and the Royster rear bag No direct contact of the tank bag on the tank, preventing damage to the paintwork Can be mounted on Lock-it tank rings or sport and mini racks with Lock-it closure. A Lock-it mounting kit is required for sport and mini racks. Art. 506100 Features: Attachment to the model-specific HEPCO&BECKER Lock-it tank ring (not included) Extremely high shape stability due to deep-drawn EVA material Waterproof, integrated inner bag with roll closure Side reflective surface - increased visibility of the motorcycle in road traffic Top shell and bottom shell made of abrasion-resistant polyester D1200 Lockable zippers - Optional accessories: security lock Carrying handle Very low weight Recommended load: 3kg (Please observe the model-specific notes on the tank ring, as well as the motorcycle manufacturer's specifications.) Recommended maximum speed: 130km/h

Compatible with the model-specific HEPCO&BECKER Lock it tank rings, this everyday little helper can be mounted on all models with a compatible fuel cap.The functional principle of the tank ring closure: The problems of placing tank bags are eliminated by magnetic centering. The handling is simple and quick. The ribs attached to the sides of the magnets mechanically secure the system. The transfer forces of the holder amount to over 70kg of vertical load, ensuring a stable and secure connection to the motorcycle at all times. To unlock, simply pull on the holding strap, allowing the magnets to release the system. The magnets align themselves, and the tank bag can be removed.Child's play and effective – simply genius. Compatible with the Royster side bags and the Royster rear bag product family No direct contact of the tank bag on the tank, preventing damage to the paintwork Can be mounted on Lock-it tank rings or sport and mini racks with Lock-it closure. A Lock-it mounting kit is required for sport and mini racks. Art. 506100 Features: Attachment to the model-specific HEPCO&BECKER Lock-it tank ring (not included) Extremely high shape stability due to deep-drawn EVA material Waterproof, integrated inner bag with roll closure Side reflective surface - increased visibility of the motorcycle in road traffic Top shell and bottom shell made of abrasion-resistant polyester D1200 Lockable zippers - Optional accessories: security lock Carrying handle Very low weight Recommended load: 3kg (Please observe the model-specific notes on the tank ring, as well as the motorcycle manufacturer's specifications.) Recommended maximum speed: 130km/h