Vehicle-Specific Information: for left sideEBC Prolite brake disc floating, Full Floater. MADE IN UK. The goal in development is to improve braking performance compared to the original brake disc. EBC uses HPSR steel with a low carbon content, which has an 18% higher coefficient of friction. This steel is significantly more resistant to rust than cast steel. Additionally, the entire surface is protected with a 3-micron thick zinc layer, which wears off in the brake pad contact zone during the bedding-in process. Only in this area can light surface rust form after prolonged periods of inactivity.   The brake discs are drilled in a bird wing design to minimize the number of holes while optimizing the cleaning of the brake disc from rainwater and brake dust. The fewer holes there are, the better the wet braking performance and the lower the wear.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus the coefficient of friction remains constant. - Braking surface drilled with an optimized hole pattern. - Galvanized for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - Independent design.Technical Data:Outer Diameter: 285 mmInner Diameter: 62.2 mmBolt Circle: 80 mmNumber of Holes: 4 Hole Diameter: 10.5 mmThickness: 4.7 mmOffset: 31.5 mmDesign: floating Manufacturer: EBC

Vehicle-Specific Information: High HandlebarOur cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of a maximum of 4.5 cm. This means that some shafts are up to a maximum of 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Product Description: original BMW workshop equipment Contents 50 ml 29.49 €/100 ml (base price indication according to §2 German Price Indication Regulation (PAngV) for sales in Germany) Safety data sheet available upon request May cause allergic reactions For professional users only

BMW Lubricant Grease Straburags for Cardan Footpeg Joints Shift Parts Product Description: original BMW workshop equipment has been used for many years for e.g. cardan shafts, plug connections, joints strongly adhesive good corrosion protection prevents tribocorrosion (combined effect of corrosion and wear) water-resistant - even under outdoor conditions approved by Knorr Brake N (12006-1.23 product info available) safety data sheet available upon request contains Pin-2(3)-enes. May cause allergic reactions content 50g 39.90 €/100g (basic price indication according to §2 German Price Indication Regulation (PAngV) for sale in Germany)

VEMO Oil Pressure Switch   ·         With sealing ring   Technical Data: Thread size M12x1.5 Switching pressure: 0.3 bar

JMP Hose Clamp   - Diameter: 13.1 to 15.3 mm- Stainless Steel 1.4307Technical Data:Type:   1 Ear Clamps Min. Clamping Range:   13.1 mmMax. Clamping Range:   15.3 mmMaterial:   Stainless Steel Color:   silver

  Bolt   Original spare partTechnical Data:Type:   Oil drain bolts    Closure bolts Thread:   M14 x 1.5 Diameter:   14 mmHead:   Flat head Drive:   Internal hexagon Surface:   No finishing Material:   Stainless steel Color:   silver Seal ring/Washers:   None Manufacturer:   Other For safety wire:   No

Nut

Brake Caliper Piston Repair Kit 38mm For models with dual disc.

Brake Caliper ScrewTechnical Data:Type: Threaded Screws Thread: M10 x 1.5 Length: 25 mmHead: Cylinder Head Drive: Internal Hexagon Surface: No Finishing Material: Stainless Steel Color: Silver Grade: 8.8 O-Ring/Washers: None Manufacturer: Other For Safety Wire: No

Brake light switch / Clutch switch

Standard lining.Technical Data:Diameter:   200 mmWidth:   25 mmGrooved:   No Includes springs:   No Manufacturer:   TRW

Fahrzeugspezifische Information:  Für Brembo Sattel Standard Belag Organisch mit Keramik-Underlayer zur Wärmedämmung . Antikorrosionslackierung , hohe Lebensdauer . Auf allen Scheiben verträglich . Solide Bremsleistung , gutes Naßbremsverhalten . Für Vorder und Hinterachse geeignet .

Die Festscheiben der Brembo Oro-Serie werden in einem Guss aus Edelstahl hergestellt. Die Fertigung entspricht hierbei den strengen Toleranzen im Bezug auf die Konstruktions- und Bauart. Durch die Bearbeitungszyklen wird eine maximale Eignung und Rundlaufsicherheit gewährleistet.   Brembo konnte aufgrund seiner umfangreichen Erfahrung die geeigneten Formen, Toleranzen und Größen für jeden Motorradtyp und Einsatz bestimmen. Tatsächlich verbessert die spezielle Formgebung der Brembo-Scheiben durch eine sorgfältige Untersuchung der Bearbeitungstoleranzen die Übertragung des Bremsmoments und bietet gleichzeitig eine verbesserte Resistenz gegen mechanische und thermische Belastungen.    

JMP starter brushes for Japanese motorcycles. As original spare parts, starter brushes are usually onlydelivered completely mounted on a base plate and aretherefore very expensive. 12.0 x 8.9 x 5.9 mm

Our cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of up to 4.5 cm. This means that some shafts are up to 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Fork Tubes by JMP   - made from high-quality raw materials - special chrome coating with low breakaway torque - each fork tube undergoes a quality inspection before delivery - manufactured on state-of-the-art CNC machines in Central EuropeTechnical Data:Upside down:   No Outer diameter:   41.3 mmInner diameter:   35 mmLength:   607 mmTop connection:   Snap ring Bottom connection:   No thread Color:   chrome

Clip Temperature Sensor

Closure Screw JMP   - M18X1.5X12- DIN 908- Zinc-platedTechnical Data:Type:   Oil Drain Screws    Closure Screws Thread:   M18 x 1.5 Diameter:   18 mmLength:   12 mmHead:   Flat Head Drive:   Internal Hexagon Surface:   Electro-galvanized Material:   Steel Color:   Silver DIN:   908 O-ring/Washers:   None Manufacturer:   JMP Bolt For Safety Wire:   No Technical Data:Thread:   M18 x 1.5 Length:   12 mmHead:   Round Head with Internal Hexagon Material:   Steel Color:   Gray For Safety Wire:   No O-ring/Washers:   No Magnetic:   No

Clutch Bolt Stainless Steel   - Total Length: 98.5mm - Diameter: 8mm

Clutch Friction Plate Note: 6 pieces are required.

For theft protection of the 2-way zipper.Prevents unauthorized opening of the tank bag. Our tank bags have eyelets on the zipper, allowing you to perfectly attach the lock.

With the help of the plastic-coated wire rope, the tank bagcan be securely connected to the bike to prevent theft.

Complete Gasket Set Athena   Athena, an international company founded in 1973, develops and manufactures gaskets, technical spare parts, and metal components for the industrial and motorcycle sectors according to the highest quality standards UNI EN ISO 9001, 9002, 14001, and UNI ISO / TS 16949.   In the off-road world, the Athena pool of engineers and technicians collaborates with the leading international teams from MXGP and AMA Supercross to develop new product lines.   Athena products undergo rigorous quality testing to guarantee customers high standards in terms of performance, competitiveness, and reliability.   Athena offers the largest selection of replacement gaskets and gasket sets available on the market, with over 40 years of experience in the industry. The Athena gasket kits are based on solid know-how, continuous technological development achieved by the in-house team of engineers and designers, and production that is strictly aligned with the parameters required by OEMs.