Vehicle-Specific Information:  for single discSV - Friction Material CompositionFull metallic sintered material with special coating.High friction coefficient ensures very good performance.Can be used on almost all discs.Only in exchange for sintered pads in the original equipment.Only conditionally suitable for racing, as there is no heat resistance above 400 degrees.Only suitable for the front axle. Restriction BMW, brake pads for BMW R65 from 85-93 with a brake disc

Angeboten wird hier ein Gebrauchtteil Fahrzeug: R1200C Independent Hersteller: BMW Zustand: normale Gebrauchsspuren Beschreibung: wird verkauft wie abgebildet Teilenummer: 61311459747

Holder for Carbon Brush  

Timing Chain Tensioner

Champion Spark Plug

  Piston Pin Clip   Size: 22X1.75mmTechnical Data:For Piston Pin Diameter:   22 mm

Vehicle-Specific Information: for raised handlebarsOur cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides permanent lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of a maximum of 4.5 cm. This means that some shafts are up to a maximum of 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Vehicle-Specific Information: for raised handlebarsOur cables and shafts are predominantly manufactured in Europe. The smooth operation is enhanced by special oils, greases, or coatings. For the cables, a high-quality silicone oil is typically used to reduce hand forces. This oil provides long-lasting lubrication and does not dry out. The shafts glide in a durable calcium grease.   To increase our delivery capability and reduce your inventory, we have consolidated certain lengths of speedometer and tachometer shafts in increments of a maximum of 4.5 cm. This means that some shafts are up to a maximum of 4.5 cm longer than the original shaft. Your advantage: With just a few shafts, you cover the entire range.

Clutch Friction Plate Note: 6 pieces are required.

Clutch Push Piston

Clutch Screw Attention: 6 pieces are required!

For theft protection of the 2-way zipper.Prevents unauthorized opening of the tank bag. Our tank bags have eyelets on the zipper, allowing you to perfectly attach the lock.

With the help of the plastic-coated wire rope, the tank bagcan be securely connected to the bike to prevent theft.

  Complete Gasket Set Athena   Athena, an international company founded in 1973, develops and manufactures gaskets, technical spare parts, and metal components for the industrial and motorcycle sectors according to the highest quality standards UNI EN ISO 9001, 9002, 14001, and UNI ISO / TS 16949.   In the off-road world, the Athena pool of engineers and technicians collaborates with the leading international teams from MXGP and AMA Supercross to develop new product lines.   Athena products undergo rigorous quality testing to guarantee customers high standards in terms of performance, competitiveness, and reliability.   Athena offers the largest selection of replacement gaskets and gasket sets available on the market, with over 40 years of experience in the industry. The Athena gasket kits are based on solid know-how, continuous technological development achieved by the in-house team of engineers and designers, and production that is strictly aligned with the parameters required by OEMs.    

Vehicle-Specific Information: Until 31.08.1980 Cruise Control Screw

SACHS diaphragm spring for the clutch pressure plate- Original equipment quality -

Dust caps from JMP   - better breakaway torque and lower friction due to special grease coatingTechnical Data:Inner diameter:   40 mmOuter diameter:   52.5 mmInstallation height:   4.6 mmTotal height:   14 mmManufacturer:   JMP

EBC CK The EBC CK standard clutch plates correspond to the original plates in dimensions and quantity. The friction material is made from a cork-based composition with a high aluminum content to minimize wear and fading. The highly compressed material also prevents the expansion of the plates and clutch slippage even under extreme load. Suitable for all types of motorcycles across all performance classes.

EBC Standard Semi-Sintered Metal Brake Pads (V-Series) The EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are organic aramid brake pads with a 30% copper content, designed for cruisers, big twins, and touring bikes. These pads are 6 times stronger than steel and are completely asbestos-free. The medium to high friction coefficient ensures strong braking power across a wide temperature range. The high braking force results in minimal wear on both the brake pad and the brake disc. EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are TÜV certified and come with an ABE!

Vehicle-Specific Information:  for simple discEBC Brake Pads Standard The EBC version SK930/ SK931/ SK932/ SK933/ SK934 contains aramid fibers that are 6 times stronger than steel and completely asbestos-free. Only low-emission components are used in production. These standard materials exceed all previous EBC standard qualities. The material mixtures, including the aramid fibers, guarantee better braking performance. High friction stability and very good temperature resistance. The lifespan is very high, and the disc wear is low. These qualities maintain their excellent properties under all weather conditions. EBC standard brake pads are TÜV certified and have an ABE.

 Milled aluminum body, suspension strut in preload and rebound (60Clicks) adjustable: by means of locking screw.

The squeegee is ideal for applying stickers and films without scratching.Due to its soft material, you can apply pressure optimally on curves for secure fixing,ensuring a long durability of the stickers/film.

Pin for Footpeg    Stainless Steel   Dimensions: - Total Length: 37mm - Head Diameter: 11mm - Bottom Diameter: 8mm  

Thanks to the use of high-quality materials, the floating-mounted discs offer excellent performance. They consist of a stainless steel friction ring and a brake pot made from CNC-machined aluminum alloy, which is connected with ten drive pins and then anodized. Technical Data:Outer Diameter: 285 mmInner Diameter: 62 mmBolt Circle: 79 mmNumber of Holes: 4 Hole Diameter: 10.5 mmThickness: 5 mmOffset: 29 mmDesign: floating Manufacturer: Brembo