Seitendeckel am Tank (unten) rechts S 1000 XR ab 2020

Discreet and yet perfectly visible - these words are probably the best way to describe the rear fairing on the left. Installed in just a few minutes. it increases the value of the motorcycle enormously. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly  

Mounted directly above the license plate holder. the upper carbon rear fairing complements the motorcycle in an exclusive way. In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. The compination with the number plate holder in Carbon is particularly good For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.  In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own. So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.   The facts:   - With general operating permit (ABE) - Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds - Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light - Delivery ready for installation - TÜV certified quality - made of prepreg material specially produced for Ilmberger - Manufactured in-house according to ISO 9001 - Attachment using the original attachment points - quick and easy assembly  

Bolted to the original attachment points. the rear fender made of carbon has proven itself in all situations. It protects the rider and motorcycle much better from the dirt coming from the rear wheel. The exposed chain guard was also lengthened in its construction compared to the original part. This means that unwanted stains - by a well-lubricated chain - on bike and rider are a thing of the past. But not only technically. but also optically. the rear fender can utilize its full potential. Installed in just a few minutes. the value of the motorcycle is increased enormously. In order to achieve a particularly harmonious overall appearance. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result. The name Ilmberger stands for highest quality and innovation in carbon fiber manufacturing. Each part is produced in our own facility. where we use specially developed prepreg for Ilmberger as the base material. This is processed in an elaborate procedure in the autoclave. which offers numerous advantages. Prepreg. a pre-impregnated carbon fabric. is characterized by an even resin distribution with a simultaneously high fiber volume content. This leads to maximum strength and increases the flexibility of the components. Processing in the autoclave. a high-pressure oven that operates under controlled temperature and pressure conditions. ensures perfect. uniform curing and a flawless surface. This method prevents air inclusions in the material and ensures consistently high quality of the parts. Our carbon parts are laminated by hand with great experience and care. allowing for consistent fiber alignment without distortion. After curing in the autoclave. the edges of the parts are precisely cut by robot to ensure a perfect fit and highest quality. A globally unique step in Ilmberger's production is the complete plastic powder coating of all carbon parts. This coating not only protects the parts from environmental influences but also gives them an incomparable depth effect. No other carbon manufacturer offers this type of sealing. which prevents the aging of the parts and significantly extends their lifespan. More information about the plastic powder coating can be found here. The final clear coat layer on this component is high-gloss and ensures a perfect. smooth surface that further emphasizes the luxurious-sporty look of our carbon parts. Each part that leaves our production is a masterpiece of technology and design that meets the highest standards. Ilmberger is not only a leading manufacturer of carbon parts for the aftermarket but also a recognized OEM producer for renowned manufacturers such as Ducati and BMW. Among other things. we manufacture parts for BMW in the World Superbike Championship (WSBK). as well as for the BMW factory team in the Endurance World Championship (EWC). where our parts are regularly put to the test under the toughest conditions. The expertise gained from this flows into each of our products. improving every single component.  The expertise gained from this flows into each of our products. improving every single component. The facts: Production in our own facility according to ISO 9001 Including ABE - Part is legal to use on the street Use of prepreg specially developed for Ilmberger Manufacturing in autoclave for maximum strength and perfect surfaces Unique plastic powder coating for protection and a special depth effect Hand lamination by experts with years of experience Precise edge cutting by robot High-gloss clear coat layer for a flawless surface No aging of parts thanks to multi-layer protection against UV light Delivery in ready-to-install condition TÜV-certified quality

When the latest high-tech materials meet modern designs. the result is often overwhelming. And the extended front fender made of carbon is not only visually impressive. Thanks to the latest technology in the field of powder coating. it is optimally protected against all common environmental influences. Thanks to its optimized shape. it also protects the water cooler behind it. In the factory state. this is constantly exposed to the thrown away dirt and other environmental influences. coming from the front wheel. In contrast. the Ilmberger Carbon fender is a little longer. Just as long as needed to keep as much dirt as possible away from the radiator and at the same time short enough to fit perfectly into the lines of the motorcycle. The name Ilmberger stands for highest quality and innovation in carbon fiber manufacturing. Each part is produced in our own facility. where we use specially developed prepreg for Ilmberger as the base material. This is processed in an elaborate procedure in the autoclave. which offers numerous advantages. Prepreg. a pre-impregnated carbon fabric. is characterized by an even resin distribution with a simultaneously high fiber volume content. This leads to maximum strength and increases the flexibility of the components. Processing in the autoclave. a high-pressure oven that operates under controlled temperature and pressure conditions. ensures perfect. uniform curing and a flawless surface. This method prevents air inclusions in the material and ensures consistently high quality of the parts. Our carbon parts are laminated by hand with great experience and care. allowing for consistent fiber alignment without distortion. After curing in the autoclave. the edges of the parts are precisely cut by robot to ensure a perfect fit and highest quality. A globally unique step in Ilmberger's production is the complete plastic powder coating of all carbon parts. This coating not only protects the parts from environmental influences but also gives them an incomparable depth effect. No other carbon manufacturer offers this type of sealing. which prevents the aging of the parts and significantly extends their lifespan. More information about the plastic powder coating can be found here. The final clear coat layer on this component is high-gloss and ensures a perfect. smooth surface that further emphasizes the luxurious-sporty look of our carbon parts. Each part that leaves our production is a masterpiece of technology and design that meets the highest standards. Ilmberger is not only a leading manufacturer of carbon parts for the aftermarket but also a recognized OEM producer for renowned manufacturers such as Ducati and BMW. Among other things. we manufacture parts for BMW in the World Superbike Championship (WSBK). as well as for the BMW factory team in the Endurance World Championship (EWC). where our parts are regularly put to the test under the toughest conditions. The expertise gained from this flows into each of our products. improving every single component.  The expertise gained from this flows into each of our products. improving every single component. The facts: Production in our own facility according to ISO 9001 Including ABE - Part is legal to use on the street Use of prepreg specially developed for Ilmberger Manufacturing in autoclave for maximum strength and perfect surfaces Unique plastic powder coating for protection and a special depth effect Hand lamination by experts with years of experience Precise edge cutting by robot High-gloss clear coat layer for a flawless surface No aging of parts thanks to multi-layer protection against UV light Delivery in ready-to-install condition TÜV-certified quality

The carbon frame cover is attached directly to the original cast frame. It covers the frame and attracts attention. The frame cover is not only convincing visually. Thanks to the high surface quality of Ilmberger Carbon. the frame cover can withstand intensive use over a long period of time. This means that there are no unpleasant work marks on the rough cast surface of the frame either after countless long tours or during daily use of the motorcycle. In order to perfect the high-quality impression. the frame cover not only runs along the vertical frame strut. where the leg rubs. but also extends far upwards. where it disappears under the tight side cover. It is therefore difficult to see from the outside where the frame cover begins and where it ends. The name Ilmberger stands for highest quality and innovation in carbon fiber manufacturing. Each part is produced in our own facility. where we use specially developed prepreg for Ilmberger as the base material. This is processed in an elaborate procedure in the autoclave. which offers numerous advantages. Prepreg. a pre-impregnated carbon fabric. is characterized by an even resin distribution with a simultaneously high fiber volume content. This leads to maximum strength and increases the flexibility of the components. Processing in the autoclave. a high-pressure oven that operates under controlled temperature and pressure conditions. ensures perfect. uniform curing and a flawless surface. This method prevents air inclusions in the material and ensures consistently high quality of the parts. Our carbon parts are laminated by hand with great experience and care. allowing for consistent fiber alignment without distortion. After curing in the autoclave. the edges of the parts are precisely cut by robot to ensure a perfect fit and highest quality. A globally unique step in Ilmberger's production is the complete plastic powder coating of all carbon parts. This coating not only protects the parts from environmental influences but also gives them an incomparable depth effect. No other carbon manufacturer offers this type of sealing. which prevents the aging of the parts and significantly extends their lifespan. More information about the plastic powder coating can be found here. The final clear coat layer on this component is high-gloss and ensures a perfect. smooth surface that further emphasizes the luxurious-sporty look of our carbon parts. Each part that leaves our production is a masterpiece of technology and design that meets the highest standards. Ilmberger is not only a leading manufacturer of carbon parts for the aftermarket but also a recognized OEM producer for renowned manufacturers such as Ducati and BMW. Among other things. we manufacture parts for BMW in the World Superbike Championship (WSBK). as well as for the BMW factory team in the Endurance World Championship (EWC). where our parts are regularly put to the test under the toughest conditions. The expertise gained from this flows into each of our products. improving every single component.  The expertise gained from this flows into each of our products. improving every single component. The facts: Production in our own facility according to ISO 9001 Including ABE - Part is legal to use on the street Use of prepreg specially developed for Ilmberger Manufacturing in autoclave for maximum strength and perfect surfaces Unique plastic powder coating for protection and a special depth effect Hand lamination by experts with years of experience Precise edge cutting by robot High-gloss clear coat layer for a flawless surface No aging of parts thanks to multi-layer protection against UV light Delivery in ready-to-install condition TÜV-certified quality

The carbon frame cover is attached directly to the original cast frame. It covers the frame and attracts attention. The frame cover is not only convincing visually. Thanks to the high surface quality of Ilmberger Carbon. the frame cover can withstand intensive use over a long period of time. This means that there are no unpleasant work marks on the rough cast surface of the frame either after countless long tours or during daily use of the motorcycle. In order to perfect the high-quality impression. the frame cover not only runs along the vertical frame strut. where the leg rubs. but also extends far upwards. where it disappears under the tight side cover. It is therefore difficult to see from the outside where the frame cover begins and where it ends. The name Ilmberger stands for highest quality and innovation in carbon fiber manufacturing. Each part is produced in our own facility. where we use specially developed prepreg for Ilmberger as the base material. This is processed in an elaborate procedure in the autoclave. which offers numerous advantages. Prepreg. a pre-impregnated carbon fabric. is characterized by an even resin distribution with a simultaneously high fiber volume content. This leads to maximum strength and increases the flexibility of the components. Processing in the autoclave. a high-pressure oven that operates under controlled temperature and pressure conditions. ensures perfect. uniform curing and a flawless surface. This method prevents air inclusions in the material and ensures consistently high quality of the parts. Our carbon parts are laminated by hand with great experience and care. allowing for consistent fiber alignment without distortion. After curing in the autoclave. the edges of the parts are precisely cut by robot to ensure a perfect fit and highest quality. A globally unique step in Ilmberger's production is the complete plastic powder coating of all carbon parts. This coating not only protects the parts from environmental influences but also gives them an incomparable depth effect. No other carbon manufacturer offers this type of sealing. which prevents the aging of the parts and significantly extends their lifespan. More information about the plastic powder coating can be found here. The final clear coat layer on this component is high-gloss and ensures a perfect. smooth surface that further emphasizes the luxurious-sporty look of our carbon parts. Each part that leaves our production is a masterpiece of technology and design that meets the highest standards. Ilmberger is not only a leading manufacturer of carbon parts for the aftermarket but also a recognized OEM producer for renowned manufacturers such as Ducati and BMW. Among other things. we manufacture parts for BMW in the World Superbike Championship (WSBK). as well as for the BMW factory team in the Endurance World Championship (EWC). where our parts are regularly put to the test under the toughest conditions. The expertise gained from this flows into each of our products. improving every single component.  The expertise gained from this flows into each of our products. improving every single component. The facts: Production in our own facility according to ISO 9001 Including ABE - Part is legal to use on the street Use of prepreg specially developed for Ilmberger Manufacturing in autoclave for maximum strength and perfect surfaces Unique plastic powder coating for protection and a special depth effect Hand lamination by experts with years of experience Precise edge cutting by robot High-gloss clear coat layer for a flawless surface No aging of parts thanks to multi-layer protection against UV light Delivery in ready-to-install condition TÜV-certified quality

With the Ilmberger Carbon side panels for your BMW M 1000 XR. you give your motorcycle not only a breathtaking. but also a light appearance. The side panels are simply mounted on the original attachment points and replace the original part. The high-quality carbon ensures an optimal balance between lightness and stability. Give your BMW M 1000 XR a unique look that will inspire you again and again. The name Ilmberger stands for highest quality and innovation in carbon fiber manufacturing. Each part is produced in our own facility. where we use specially developed prepreg for Ilmberger as the base material. This is processed in an elaborate procedure in the autoclave. which offers numerous advantages. Prepreg. a pre-impregnated carbon fabric. is characterized by an even resin distribution with a simultaneously high fiber volume content. This leads to maximum strength and increases the flexibility of the components. Processing in the autoclave. a high-pressure oven that operates under controlled temperature and pressure conditions. ensures perfect. uniform curing and a flawless surface. This method prevents air inclusions in the material and ensures consistently high quality of the parts. Our carbon parts are laminated by hand with great experience and care. allowing for consistent fiber alignment without distortion. After curing in the autoclave. the edges of the parts are precisely cut by robot to ensure a perfect fit and highest quality. A globally unique step in Ilmberger's production is the complete plastic powder coating of all carbon parts. This coating not only protects the parts from environmental influences but also gives them an incomparable depth effect. No other carbon manufacturer offers this type of sealing. which prevents the aging of the parts and significantly extends their lifespan. More information about the plastic powder coating can be found here. The final clear coat layer on this component is high-gloss and ensures a perfect. smooth surface that further emphasizes the luxurious-sporty look of our carbon parts. Each part that leaves our production is a masterpiece of technology and design that meets the highest standards. Ilmberger is not only a leading manufacturer of carbon parts for the aftermarket but also a recognized OEM producer for renowned manufacturers such as Ducati and BMW. Among other things. we manufacture parts for BMW in the World Superbike Championship (WSBK). as well as for the BMW factory team in the Endurance World Championship (EWC). where our parts are regularly put to the test under the toughest conditions. The expertise gained from this flows into each of our products. improving every single component.  The expertise gained from this flows into each of our products. improving every single component. The facts: Production in our own facility according to ISO 9001 Including ABE - Part is legal to use on the street Use of prepreg specially developed for Ilmberger Manufacturing in autoclave for maximum strength and perfect surfaces Unique plastic powder coating for protection and a special depth effect Hand lamination by experts with years of experience Precise edge cutting by robot High-gloss clear coat layer for a flawless surface No aging of parts thanks to multi-layer protection against UV light Delivery in ready-to-install condition TÜV-certified quality

The passenger seat cover in carbonfiber for the BMW S 1000 XR MY2020 is a direct replacement for the original component. This front fender contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality