Vehicle-Specific Information: for left sideEBC Prolite brake disc floating, Full Floater. MADE IN UK. The goal in development is to improve braking performance compared to the original brake disc. EBC uses HPSR steel with a low carbon content, which has an 18% higher coefficient of friction. This steel is significantly more resistant to rust than cast steel. Additionally, the entire surface is protected with a 3-micron thick zinc layer, which wears off in the brake pad contact zone during the bedding-in process. Only in this area can light surface rust form after prolonged periods of inactivity.   The brake discs are drilled in a bird wing design to minimize the number of holes while optimizing the cleaning of the brake disc from rainwater and brake dust. The fewer holes there are, the better the wet braking performance and the lower the wear.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus the coefficient of friction remains constant. - Braking surface drilled with an optimized hole pattern. - Galvanized for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - Independent design.Technical Data:Outer Diameter: 285 mmInner Diameter: 62.2 mmBolt Circle: 80 mmNumber of Holes: 4 Hole Diameter: 10.5 mmThickness: 4.7 mmOffset: 31.5 mmDesign: rigid Manufacturer: EBC

Vehicle-Specific Information: for right sideEBC Prolite Brake Disc, Full Floater   EBC replaces the rigid original disc with a Full Floater brake disc The manufacturing of the complex and expensive Full Floaters offers significant advantages when braking. The brake ring, sawed, drilled, and ground from forged HPSR steel bars, can expand freely even during repeated hard braking, for example, during mountain descents, without deforming. Here, the low carbon content of the used HPSR steel proves beneficial, as it ensures very little microstructural change in the steel under the thermal stress of heating and cooling the brake disc in tough road conditions. An EBC Full Floater brake disc is always a significant gain in safety.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus the coefficient of friction remains constant. - Braking surface drilled with an optimized hole pattern. - Zinc-coated for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - EBC recommends EBC Double-H sintered brake pads for best braking performance. - Independent design.Technical Data:Outer Diameter:   285 mmInner Diameter:   62.2 mmBolt Circle:   80 mmNumber of Holes:   4 Hole Diameter:   10.5 mmThickness:   4.7 mmOffset:   31.5 mmDesign:   rigid Manufacturer:   EBC

Die Festscheiben der Brembo Oro-Serie werden in einem Guss aus Edelstahl hergestellt. Die Fertigung entspricht hierbei den strengen Toleranzen im Bezug auf die Konstruktions- und Bauart. Durch die Bearbeitungszyklen wird eine maximale Eignung und Rundlaufsicherheit gewährleistet.   Brembo konnte aufgrund seiner umfangreichen Erfahrung die geeigneten Formen, Toleranzen und Größen für jeden Motorradtyp und Einsatz bestimmen. Tatsächlich verbessert die spezielle Formgebung der Brembo-Scheiben durch eine sorgfältige Untersuchung der Bearbeitungstoleranzen die Übertragung des Bremsmoments und bietet gleichzeitig eine verbesserte Resistenz gegen mechanische und thermische Belastungen.

EBC Standard Semi-Sintered Metal Brake Pads (V-Series) The EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are organic aramid brake pads with a 30% copper content, designed for cruisers, big twins, and touring bikes. These pads are 6 times stronger than steel and are completely asbestos-free. The medium to high friction coefficient ensures strong braking power across a wide temperature range. The high braking force results in minimal wear on both the brake pad and the brake disc. EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are TÜV certified and come with an ABE!

Vehicle-Specific Information:  from 01.08.1988 for 2 disc brakes  EBC Standard Semi-Sintered Metal Brake Pads (V-Series)   The EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are organic aramid brake pads with a 30% copper content for cruisers, big twins, and touring bikes. These pads are 6 times stronger than steel and are also completely asbestos-free. The medium to high friction value ensures high braking power over a wide temperature range. The high braking power results in minimal wear of the brake pad and brake disc. EBC Standard Semi-Sintered Metal Brake Pads (V-Series) are TÜV certified and have an ABE!

Vehicle-Specific Information:  from 01.08.1988 for 2 disc brakes  EBC Brake Pads Double - H Sinter Material MADE IN USA, among others for motorcycles with original sintered pads A quality with the highest braking power, extreme durability, and without any fading, especially for use in heavy and fast machines or in road racing. Perfectly suitable for INOX or EBC Pro-Lite brake discs. Brake pads are also optimal for cast brake discs. Double - H brake pads are TÜV certified and have an ABE.

Vehicle-Specific Information: for double disc EBC Brake Pads Double - H Sinter Material MADE IN USA, among others for motorcycles with original sintered pads A quality with the highest braking power, extreme durability, and no fading, especially for use in heavy and fast machines or in road racing. Perfectly suitable for INOX or EBC Pro-Lite brake discs. Brake pads are also optimal for cast brake discs. Double - H brake pads are TÜV certified and have an ABE.