Vehicle-Specific Information:  from 01.08.1988 for 2 disc brakes  EBC Brake Pads Double - H Sinter Material MADE IN USA, among others for motorcycles with original sintered pads A quality with the highest braking power, extreme durability, and without any fading, especially for use in heavy and fast machines or in road racing. Perfectly suitable for INOX or EBC Pro-Lite brake discs. Brake pads are also optimal for cast brake discs. Double - H brake pads are TÜV certified and have an ABE.

The fixed discs of the Brembo Oro series are made from a single casting of stainless steel. The manufacturing process adheres to strict tolerances regarding design and construction. Through the machining cycles, maximum suitability and run-out safety are ensured.   Due to its extensive experience, Brembo has been able to determine the appropriate shapes, tolerances, and sizes for every type of motorcycle and application. In fact, the special shaping of the Brembo discs, through careful examination of the machining tolerances, improves the transfer of braking torque while simultaneously providing enhanced resistance to mechanical and thermal stresses.Technical Data:Outer Diameter:   260 mmInner Diameter:   62 mmBolt Circle:   79 mmNumber of Holes:   5 Hole Diameter:   8.5 mmThickness:   4 mmDesign:   fixed Manufacturer:   Brembo

EBC Prolite Brake Disc Floating, Full Floater. MADE IN UK. The goal in development is to improve braking performance compared to the original brake disc. EBC uses HPSR steel with a low carbon content, which has an 18% higher coefficient of friction. This steel is significantly more resistant to rust than cast steel. Additionally, the entire surface is protected with a 3-micron thick zinc coating, which wears off in the brake pad contact zone during the bedding-in process. Only in this area can light surface rust form after prolonged periods of inactivity.   The brake discs are drilled in a bird wing design to minimize the number of holes while optimizing the cleaning of the brake disc from rainwater and brake dust. The fewer holes there are, the better the wet braking performance and the lower the wear.   - Brake ring made from forged HPSR steel with low carbon content, machined. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus the coefficient of friction remains constant. - Braking surface drilled with an optimized hole pattern. - Galvanized for protection against corrosion. - Hub made from anodized aluminum. - Minimal manufacturing tolerances. - Independent design.Technical Data:Outer Diameter:   260 mmInner Diameter:   62.2 mmBolt Circle:   79 mmNumber of Holes:   5 Hole Diameter:   8.5 mmThickness:   5 mmOffset:   35.8 mmDesign:   floating Manufacturer:   EBC

Original BMW Spare Part The brakes of your motorcycle are the most important component when it comes to safety. Therefore, they must always be in perfect working order. After all, it can sometimes come down to millimeters and milliseconds. We recommend using original BMW brake pads on the original brake discs. BMW has coordinated the materials of the brake disc and brake pad to work together. This means optimal braking performance with minimal wear. Additionally, the fastening parts on the brake calipers should be regularly replaced. They are also subject to wear. Only when everything in the braking system is free to move can it operate optimally!

EBC Prolite Brake Disc, Full Floater   EBC replaces the rigid original disc with a Full Floater brake disc. The manufacturing of the complex and expensive Full Floater offers significant advantages when braking. The brake ring, sawed, drilled, and ground from forged HPSR steel bars, can expand freely even during repeated hard braking, such as when descending mountain passes, without deforming. Here, the low carbon content of the used HPSR steel proves beneficial, as it ensures minimal microstructural changes in the steel under the thermal stress of heating and cooling the brake disc in demanding road conditions. An EBC Full Floater brake disc is always a significant gain in safety.   - Brake ring machined from forged HPSR steel with low carbon content. - Therefore, no warping of the brake disc even under maximum load. - No glazing of the braking surface, thus maintaining a constant coefficient of friction. - Braking surface drilled with an optimized hole pattern. - Zinc-coated for protection against corrosion. - Hub made of anodized aluminum. - Minimal manufacturing tolerances. - EBC recommends EBC Double-H sintered brake pads for optimal braking performance. - Independent design.Technical Data:Outer Diameter:   260 mmInner Diameter:   62.2 mmBolt Circle:   79 mmNumber of Holes:   5 Hole Diameter:   8.5 mmThickness:   5 mmOffset:   35.8 mmDesign:   floating Manufacturer:   EBC