Original BMW Spare Part Additional Information The part with the BMW part number 51 14 8 164 924 is used on the following vehicles:

Replaceable open cartridge kit from YSS.Adjustable spring preload, rebound, and compression damping through a specially developed cap. The included stiffer spring can be replaced if necessary. Transforms a dull stock fork into a perfectly adjustable fork.Technical Data:Spring Type: Linear Length: 380 mmDiameter 1: 39.5 mmDiameter 2: 39.5 mmSpring Rate 1: 6 N/mmRecommended Viscosity: 5W Manufacturer: YSS

Diese progressiven Austauschfedern sind perfekt auf das Federbein der BMW F800GS (Heavy Load)  und BMW HP2 abgestimmt. Die Gabelfeder hat so eine bessere Abstimmung für die Anforderungen des Motorradreisens. Zu dem werden sie ein deutlich verbessertes Ansprechverhalten und höhere Reserven im Grenzbereich erfahren. Die Austauschfedern werden vom holländischen Fahrwerksspezialisten Hyperpro in Europa gefertigt.Für die Verwendung mit unserem BMW F800GS und BMW HP2 Tankumbau dringend empfohlen.Bei allen Fahrwerkslösungen sollten Heck- und Frontbereich des Motorrades angepasst werden.=> Beim Austausch nur einer Komponente, wird kein optimales Fahrverhalten erzielt.Lieferung inklusive: ausführlicher Anbauanleitung, dem passenden Gabelöl und einer Paste zur Verbesserung der Gleitfähigkeit der Tauchrohre.Unserer Empfehlung: Lassen sie den Umbau von einer Fachwerkstatt durchführen.Hinweis: BMW F800GS bis 2012

Simmerring and dust cover from SKF:- Less friction (approx. -20%) compared to conventional sealing rings- Use of a self-lubricating material- Less stick-slip- (Stick-slip = breakaway force caused by static friction)- Significantly improved sealing effect- Less air entry into the fork- Less dirt entry into the fork- thus less wear on bushings and oil- thus maintaining the optimal sliding properties of the fork- Increased long-term sealing- Excellent water, dirt, and air tightness. UV resistant For:- BMW F800GS 2006-2013 - BMW HP 2- BMW G450X- BMW G650X Dimensions:Fork sealing ring Ø45 x 58.3 x 11 mm / Wiper Ø 45 x 55.7 x 5.5 mmScope of delivery:1 piece sealing ring1 piece dust cover(Two sets are required for a complete fork)

Simmerring and Dust Cap from SKF:- Less friction (approx. -20%) compared to conventional sealing rings- Use of a self-lubricating material- Less stick-slip - (Stick-slip = breakaway force caused by static friction)- Significantly improved sealing effect - Less air entry into the fork- Less dirt entry into the fork - thus less wear on sliding bushings and oil - thus maintaining the optimal sliding properties of the fork- Increased long-term tightness - Excellent water, dirt, and air tightness. UV resistantDimensions:Fork sealing ring Ø43 x 52.9 x 9.5mm / Wiper Ø43 x 53.4 x 5.8 mmScope of delivery:1 piece sealing ring1 piece dust cap(Two sets are required for a complete fork)

The Touratech Suspension Lowering Kit from the Dutch suspension specialist Hyperpro. The set includes replacement fork springs and a replacement spring for the shock absorber. With this spring set, you achieve a sensible lowering of 50mm while maintaining consistently good riding characteristics - of course, some ground clearance is lost. The progressive springs are perfectly tuned to the BMW F800GS / Adventure. After the conversion, the suspension offers significantly improved responsiveness and higher safety in the limit range. By replacing the springs front and rear, the balance of your motorcycle is preserved.Info: Fits only for * BMW F800GS / Adventure from 2013*The replacement springs can be used with or without ESA equipment.Delivery includes: detailed installation instructions, the appropriate fork oil, and a paste to improve the sliding properties of the fork tubes.Our recommendation: Have the conversion carried out by a specialist workshop.Note:For the safe stand of your BMW F800GS / Adventure after lowering, we recommend the shortened side stand and/or optionally the shortened center stand. These components can be obtained from your BMW dealer.

A lowering of the front with replacement fork springs from the Dutch suspension specialist Hyperpro. With this spring set, you achieve a sensible lowering of 50mm without compromising handling characteristics - of course, some ground clearance is lost. The progressive springs are perfectly tuned to the BMW F800GS / Adventure and offer significantly improved responsiveness and higher safety in the limit range compared to the original fork springs. Info: Fits only for *BMW F800GS / Adventure*The replacement springs can be used with or without ESA equipment.For all suspension solutions, the rear and front areas of the motorcycle should be adjusted.=> The suitable components for the rear of the BMW F800GS / Adventure are:=> Touratech Suspension shock absorber *rear* BMW F800GS *lowering* 01-048-5864-0=> Touratech Suspension shock absorber *rear* BMW F800GS Adventure *lowering* 01-048-5884-0=> When replacing only one component, optimal handling is not achieved.Delivery includes: detailed installation instructions, the appropriate fork oil, and a paste to improve the sliding properties of the fork tubes.Our recommendation: Have the conversion carried out by a specialist workshop.Note:For the safe stand of your BMW F800GS after lowering, we recommend the shortened side stand and/or optionally the shortened center stand. These components can be obtained from your BMW dealer.

These progressive replacement springs are perfectly matched to the fork and shock absorber of the BMW F800GS. The shock absorber and the fork provide a better setup for the demands of motorcycle touring. Additionally, you will experience a significantly improved response and higher reserves in the limit range. The replacement springs are manufactured in Europe by the Dutch suspension specialist Hyperpro.The replacement springs can be used with or without ESA equipment.Delivery includes: detailed installation instructions.Our recommendation: Have the conversion carried out by a specialist workshop.

The Touratech Suspension Lowering Kit. The set includes replacement fork springs and a replacement spring for the shock absorber. With this spring set, you achieve a sensible lowering of -50mm while maintaining consistently good riding characteristics - of course, some ground clearance is lost. The progressive springs are perfectly tuned to the BMW F800GS. After the conversion, the suspension offers significantly improved responsiveness and higher safety in critical situations. By replacing the springs at the front and rear, the balance of your motorcycle is preserved.   Info: Fits only for “BMW F800GS (2008-2012)“   Scope of delivery: - Fork springs for the original fork -50mm - Replacement spring for original shock absorber -50mm - including detailed installation instructions. - suitable fork oil. - Paste to improve the sliding properties of the inner tubes.   Our recommendation: Have the conversion carried out by a professional workshop. Installation note: Fork tool 01-300-5844-0 (HP-T65) is required for installation.   Info: The side stand and main stand may need to be adjusted in length.   Do you have further questions? We are happy to advise you personally, please contact us. Email: [email protected] Phone +49 (0)7728-9279-1555   Please use our suspension check form and send us the completed form.